Dave are there any common freqs that MT63 uses? I'm up for a try! ...DOUG, KD4MOJ 30MDG#1076, FH#1125 ... From: MT63@yahoogroups.com...
3778
David Kleber
kb3fxi
Dec 28, 2008 11:17 pm
Doug, I've had some success on 14.1095 USB and much less success on 7.0905 USB. Nothing much at all down on 80m that I've seen with the exception of a few...
3779
n9aop2000
Jan 3, 2009 1:56 am
I found that I have to fish where the psk folks are ie. 14.070.15. Getting someone to go to MT63 is not as easy as having them switch to hellschreiber or MFSK...
3780
Craig Wallen
kf4hou
Jan 3, 2009 3:33 pm
I have been fairly active on 80m mt63 here lately with pretty good results, if you like a sked let me now on the 80m band .. but, for some reason I am having a...
3781
Cliff Manis
cmanis1
Jan 3, 2009 5:05 pm
Rick and all I like to do MT63 anytime, and will be looking for a contact from time to time on 40 or 20 meters. Yes, I agree - the USAF MARS nets are...
3782
list2
stevenpituch
Jan 3, 2009 7:31 pm
Hi Craig and All, This brings up an interesting phenomenon that I discovered while working with MT63 for MARS. From what I understand MT63 was designed to...
3783
Simon (HB9DRV)
simonbrown42
Jan 3, 2009 7:34 pm
Just offset the radio by x Hz. I will look at this in the future, but these MARS guys are going against the MT63 proposal from the guy who invented it. Simon...
3784
David Kleber
kb3fxi
Jan 4, 2009 1:18 am
Craig, I think I watched your qso for about 45 minutes the other night from here in Pittsburgh, PA. 100% copy on both stations here. I've never used .5k...
3785
David Kleber
kb3fxi
Jan 4, 2009 1:32 am
Steve, I was of the understanding that the standard was 500 Hz at the bottom of the signal, too. But can't you simply put your rig in fine VFO tune and move...
3786
list2
stevenpituch
Jan 4, 2009 1:56 am
Hi Dave, The problem is that during Hurricane Ike, Texas Army MARS demonstrated that mixed mode operation was more efficient than either an all MT63 net, or an...
3787
David Kleber
kb3fxi
Jan 4, 2009 2:57 am
Very interesting, Steve. Which brings up another subject, hence the change in the subject line. I really wish we (Amateur Service) would move to regs by...
3788
Jim Haynes
jhaynesatalumni
Jan 4, 2009 3:14 am
However I guess if they were using 2KHz MT63 rather than 1KHz then you would again want the MT63 to start at 500 Hz and end at 2500 Hz, rather than starting at...
3789
David Little
dalite01
Jan 4, 2009 3:22 am
This is the reason for the 500 HZ start freq; especially on NTIA freqs which are channelized. It is hard to move from the concept of "center of intelligence",...
3790
list2
stevenpituch
Jan 4, 2009 2:17 pm
Hi Dave and all, Thanks for the change in subject line. Yes, well I guess the ARRL assumed that it was such a good idea that they did not need to work on grass...
3791
Karl Larsen
k5di3
Jan 4, 2009 5:27 pm
I really am wondering how many of you have actually tuned in a digital signal. It is very simple with almost all the software for the digital modes. I seem to...
3792
Craig Wallen
kf4hou
Jan 4, 2009 5:44 pm
Something I have learned is it is almost essential to have your TX frequencies locked , so you can have the ability to move around the RX in MT63. There are a...
3793
Paul L Schmidt, K9PS
paul_schmidt...
Jan 5, 2009 10:32 pm
Indiana Navy-Marine Corps MARS uses 2 kHz 95+% of the time; only dropping down to 1 kHz if conditions are extremely bad (High QRN, etc.). Of course, when...
3794
David Kleber
kb3fxi
Jan 22, 2009 11:27 pm
Hello all, Harry Bloomberg (W3YJ - Assistant Section Emergency Coordinator for Digital Communications, WPA) and I will be the featured guests for the January...
3795
David Kleber
kb3fxi
Jan 25, 2009 8:19 pm
Hello all, Based on many comments and several new hams jumping in on our wpaNBEMS net this morning on 80m, I'd say the ARRL Atlantic Division Webinar on NBEMS...
3796
jeff
wb4wxd
Jan 26, 2009 4:53 pm
I want to use my old model FT-817 on MT63 and VHF and have not been able to pass audio. I am connected to the data port as normal for HF but can't see to get...
3797
RobertCGRO
Jan 31, 2009 2:55 pm
Happy New Year to all! I've gone through the old messages on the "floating point" error with MT63. What I'm seeing is the ATAN2 domain error (basically same as...
3798
David Kleber
kb3fxi
Jan 31, 2009 4:42 pm
Robert, Here in Western PA we're having great success with FLDIGI. I know your question is focused on getting the old terminal running, but I'd suggest giving...
3800
Steve Friis
sfriis2002
Mar 6, 2009 5:06 am
This is Val, Steve's wife. I wanted to let everyone know that Steve died Thursday afternoon at home. If anyone needs to get hold of me, my email is...
3802
rabe_marsh
Apr 26, 2009 6:26 pm
I have no idea how to utilize the WRAP functions on the Macintosh version. There seems to be no application for the Mac, and nothing is said in the help...
3803
David Kleber
kb3fxi
Jun 4, 2009 11:06 pm
Hello all, The NBEMS team has provided a very useful tool for MT63 (as well as any other mode) with a new feature called WRAP. WRAP is a simple program that...
3804
David Kleber
kb3fxi
Jul 14, 2009 11:23 am
Here's part of a post I made to our wpaNBEMS yahoo group which has tips for newer users of MT63. Try NBEMS/FLDIGI with the WRAP checksum feature. We had a...
3805
Don
kb9umt
Aug 8, 2009 7:58 pm
30 Meter Multi Mode Weekend When: August 22nd & 23rd Where: 10 MHz - 30 Meter Band Objective: To promote experimenting and using different digital modes on...
3806
kb3fxi
Sep 17, 2009 12:09 am
Hello all, Several operators and groups in digital emcomm are considering a bulletin transmission on a fixed 40m frequency and schedule. The plan would be to...
3807
kc0pto
Oct 25, 2009 2:59 am
Not MT63 related, but thought maybe some of you may be interested in working the Veterans Day Special Event Station that the Emporia (KS) Amateur Radio Society...
3808
kb3fxi
Oct 30, 2009 3:31 am
Hello all, Western Pennsylvania will be active with the SET drill this Saturday morning with NBEMS/FLDIGI on 3.5835 USB, Olivia 8/500 for keyboard and MT63 1k...
