Hi Gloria, I have the same problem. Jim, I have already installed Ver 2.21 and it has still not solved the problem. Has anyone else reported that the new ...
I am about to buy a pre owned MC10000 from an elderly lady. It is just one year old and comes with only the Janome Card Reader 10000. I would like to conect it...
In a message dated 02/01/2002 10:09:18 AM Eastern Standard Time, MC10000@yahoogroups.com writes: << From: "Pat B." <psst_pat@...> Subject: CompactFlash...
OK, this time I have ordered what *SHOULD* be a 30-day supply based on your "votes." All outstanding orders are shipping today, and the site is now open to...
If any of you would like to participate in "Stitch-a-Square" program for Cotlands Care Center and Hospice for abandoned, abused and HIV+ babies go to: ...
Is there a way to convert raster (BMP, Etc.) based clipart to a 2- pixel wide outlined image in PaintShop Pro? Otherwise, does this capability exist in...
Melody, Jim didn't say it... but I will. It sounds like you could benefit from a support table. I'll bet you had a reasonably weighty garment attached to the...
Hi Jim! I have been trying to embroider with Puffy foam and I keep getting thread nests underneath. Have you used it at your shop and do you have any insights...
I have the MC10000, and Customizer 10K, and Buzz Tools Plus. Is there anywhere I can mirror image a design? I hope I'm just missing it somewhere. Would Embird...
Jim, Probably a stupid question but, is there anyway to take one of the designs from a 10000 card and put it in either Digitizer or GigaHoop or somewhere so I...
Ah Ha... you must be referring to our ANZAC Bikkies...Oz for biscuit aka as Cookies to you guys "up there"...my hubby is originally from Long Island so I am...
Dear Jim, I too have this same problem. I emailed you about it before. I cannot get it to work in my machine or the one at my dealers. I have the San Disk....
What has been the experience of users who have used a tilt adapter to tilt the MC10000 for "easier" sewing or emb.? Carpal tunnel and bending the neck both...
I have been using the tilt thing on my 10000 without any problem, even with the b hoop. [Non-text portions of this message have been removed]...
4282
RRlead@...
Feb 4, 2002 3:31 am
Hi, I have a tilt table under my machine, I use it for regular sewing and embroidery. It has not changed anything on my machine. I also have a bad neck and...
4283
Kenneth Lyman
az_ajgray@...
Feb 4, 2002 3:31 am
I have upgraded Customizer to 2.2a and my Machine to 2.21 and cannot load designs to the card, it says "100 designs are registered no design can be...
Actually, the card is a 48MB Sandisk Compact Flash Card. And you are right, the dealer could not get the card to work in her machines either. As I've been ...
Hi Jim, I would just like to say that I just got this table from you and had the opportunity to put it to good use this weekend for the first time at a three...
Great feedback, regret you have so many to wade through on, I do hope everyone was refereing to the "Tilt'able tm, I have seen this is specialitly sewing...
A few questions: 1. Is it "normal" for the needle to shift left of center position when snitching in embroidery mode?? The needle is in the correct position...
wendy, glad to read your number one here. i was having the same problem. i thought for a while there, i was the only one having the problem. if there is any...
4290
Ubrokus@...
Feb 5, 2002 4:10 am
Haven't tried this yet with my 10000 - however , a friend gave me "rubber door stops" - look like a wedge. I put those under my sewing machines when I am free...
4291
DECATAR@...
Feb 5, 2002 4:10 am
In a message dated 02/04/2002 2:24:53 PM Central Standard Time, DrWWood@... writes: << If you are breaking needles, the most common cause is the thread...
Apologies if this has already been posted... I just purchased the gigahoop, and wanted to know if I can use Digitizer. I don't see the option when selecting...
Jim, I want to purchase one of the tables you've been talking about but couldn't locate you on a search. Would you please provide me with directions to get one...
4294
Happy Tilter
Feb 5, 2002 1:55 pm
I have used the Tilt Table since I found it 3 years ago. I have never had a problem, it has never walked on me, Embroidery is not effected in any way and I...
tell me, can we get extra spool holders from janome ______________________________________________________________ Just ask you dealer for a "Large spool cap."...
Jim, I have the 10000, I ordered the single hole needle plate, and they gave me the plate that says for the 9000 only. Is this the one that fits the 10,000....
