I appear to have hit upon a problem with the calibration of my LP-100 #139. All has gone well until I got to the Master/Pwr/Trim and Fine/Pwr/Trim screens. On...
Yep, It is a bug which Larry will fix in the next release. The work-around is to go back to the main power screen and switch to "fast" mode, which is indicated...
I have seen a comment that the new Windows Vista operating system does **NOT** support serial (COM) ports or parallel (LPT) ports. Can anyone shed any light...
That bug was fixed a long time ago, unless it crept back in due to a cut-an-paste error. I assume you are running ver. 1.1.2 or 1.1.3, David. You can see the...
Larry, Will you be putting V1.1.3 out on the website or somewhere else so that those of us that have earlier versions can upgrade our firmware? 73, Ted K9IMM ...
Senility is catching up with a vengeance - where's the link to the programming side of the LP-100? I am sure I read it but can't for the life of me remember...
It's there now, even though I haven't announced it... that's because I'm close to releasing version 1.1.4, which will add several new setup screens for editing...
Larry, Do you have a set of "real world" ball park settings for the Gain and Phase numbers that we should shoot for on all the bands? My 160 Meter numbers are...
The Gain/Phase settings are highly dependent on a number of things, including xfmr winding and orientation, interconnecting cable variations, attenuator...
NO! Only going from the old PIC to the new. Even then, you can stick with the old calibration, but you won't get the added benefit of the new vector accuracy...
No, just an older one. I have made some slight running changes as the second run has progressed. You can download and program 1.1.3 if you want from the...
Hi Larry, I'd like to send in my LP-100 for upgrade and calibration. Do you need the directional coupler, or just the meter? Thanks, Mike, K4GU [Non-text...
I was getting the subject error on an XP system. It failed on a quad serial PCI card and on two USB/serial adapters. I just want to report that the problem...
Thanks for the feedback, Bill. I wonder what service pak you're using? XP is a funny animal. Larry N8LP ... [Non-text portions of this message have been...
... Hi Larry, it was failing with ServicePak 2 & all available updates. That's where it is now & it's working. All the same devices & drivers. I suspect...
Larry, Please don't be horrified, but ..... I'm thinking about respraying the case a different colour when I get my LP-100 kit to match my TenTec Corsair...
I'm not the best guy to answer about painting, but I suspect it would be possible to do a good job. The powder coated surface should make a good base I think. ...
Hi Larry, I just wanted to check in with you on the processor swap for the earlier LP-100s. Have you sent out any replacement processors yet? I'm still running...
I sent several chips to beta testers to check on the feasibility of field upgrades. The results were mixed. I think two had no problem but the third did. I am...
I have discovered a bug which might be causing problems with some users being able to connect to the LP-100 with the VCP. The problem occurs because the call...
I have noted another possible problem with VCP. I use COM4 to communicate with the LP-100, which works very well. I, however, can't update the firmware thru...
The MCLoader programming software is independent of the VCP. It is commercial software that I am licensed to distribute. I will talk to the developer to see if...
COM3 and COM4 on my system are on a PCI serial port adapter board. They are not USB adapters. They do use the standard addresses and interrupts as the ...
That's very odd - I suggest checking you have the latest drivers. There's no reason why a software program should have problems such as you describe unless...
Hi Larry, The meter arrived at my QTH last week. It is a really nice piece of equipment. I immediately hooked it up with my IC7800. It is amazing to note...
