Neal, Thanks for the information. I'm working on a HF Projects 35 watt Amp that should allow a little more power output to give the AT-100 room to tune. 73, ...
3124
jadale55068
Jul 2, 2008 1:44 pm
I was working Field Day by phone with my Icom 706MkIIG running on a 12 V marine deep cycle battery. It was one of the larger battery's. After running for a few...
3125
Craig
cpu_nut
Jul 2, 2008 1:49 pm
Was the 12.6V measured while under the transmitting load? Craig ... From: jadale55068 <jd1dale@...> Subject: [LDG-auto-tuners] Z-11 Pro and 706 MkIIG...
3126
jadale55068
Jul 2, 2008 5:14 pm
No it was not. I was when I was listening. Jim...
3127
wolfrobert
Jul 2, 2008 5:14 pm
... important I have looked at the Russian translation and would like to go a step further in the remoting of the Z-100. I would like to power and control the...
3128
ldgelectronics
Jul 2, 2008 5:16 pm
Field Day? Were there any other transmitters going nearby? Dwayne Kincaid LDG...
3129
jadale55068
Jul 2, 2008 7:55 pm
There was one other station running nearby on 20 CW. But he was running when I did not have the problem. Jim...
3130
wolfrobert
Jul 2, 2008 7:55 pm
... important I have looked at the Russian translation and would like to go a step further in the remoting of the Z-100. I would like to power and control the...
3131
Tony Farrow
ajfoxtrot
Jul 3, 2008 2:19 pm
Hi Jim, The IC-706IIG requires 13.8v +/- 15%, so perhaps under load your battery's voltage fell below this minimum and the rig's TX power fell away? Cheers, ...
3132
jadale55068
Jul 3, 2008 7:36 pm
Tony Thanks for the idea. At +-15 the low side will be 11.7 volts. I also had the problem when I was on receive. Unless the voltage out on the 706s auto tune...
3133
Neal Enault
wa6ocp
Jul 5, 2008 5:29 pm
I recently added an FT-897D to the shack and hit the problem of the Z11Pro trying to autotune when I transmitted on 432. Didn't happen on 144. I went back and...
3134
Rick Armitage
va2vft
Jul 6, 2008 12:56 am
I have an AT1000 tuner and considering a DX Engineering Thunderbolt 160-10 meter vertical antenna. It uses a 43' Radiator and their 4:1 tuner balun the ...
3135
coa132435
Jul 6, 2008 5:00 am
Rick, I have the 33ft and the 4:1 balun. The AT-1000Pro matches all bands with the exception of 6m. There is alot of "heat" about the losses in the transmision...
3136
KONI
dg8fdd
Jul 6, 2008 3:30 pm
On Jim's website the Installprocedure is described as following: My control software is a single file at200pc.pyw that runs on both Windows and Linux, and...
3137
Jim
gvojim
Jul 8, 2008 3:16 am
Does anyone know where I can obtain a Y cable (splitter) for the FT-857D CAT connector? That's the one that the LDG Yaesu one touch tune interface uses? I am...
3138
jimahlstrom
Jul 8, 2008 5:18 pm
... There is a link on my web page, or just use this URL: http://james.ahlstrom.name/at200pc.pyw Jim N2ADR...
3139
KONI
dg8fdd
Jul 8, 2008 7:26 pm
Jim, I think the at200pc.pyw file is the renamed at200pc.pyw.txt - am I right? Into which directory shall I do it in? in the maindirectory of Python25? does...
3140
Herbert Snapp
snappysnapp
Jul 9, 2008 3:04 am
I have an AT-1000 and use it with a B&W Folded Diapole. It works great. I have had no problems. Herb ... From: Rick Armitage <ve3vft@...> To:...
3141
Lars Pettersson
sm4ive
Jul 11, 2008 1:39 pm
Anyone got a manual for the AT-11 Ver 3.0 from Juli 1996 Regards Lars SM4IVE...
3142
tom burkhart
tburkhar2
Jul 13, 2008 9:20 pm
I had a thunderstorm come thru today, and the at-100 is no longer working. I have 12 volts going into the input, but no leds will light, and it will not tune,...
3143
jimahlstrom
Jul 14, 2008 7:11 pm
... right? No. Rename the file back to at200pc.pyw. ... It doesn't matter. I use S:/python for my Python programs. ... Yes, it will start even if you have no...
3144
Peter M. Schulz
vk2vz
Jul 14, 2008 7:11 pm
... light, ... the ... ideas? ... Hi, See if your plugpack 12 volt gone, or there is a regulator inside the unit,, if all fails it could be the Micro inside ...
3145
Chris
bchriste9149
Jul 14, 2008 7:23 pm
Have you tried to reset the at-100? Reset is to hold "FUNC + ANT + TUNE " on power up. Bob (WU9Q)...
3146
KONI
dg8fdd
Jul 15, 2008 2:12 am
Jim, so I think that maybe I've the wrong sys-files downloaded, because of on my win xp the directory is named python 25. so what is to download for win xp?...
3147
KONI
dg8fdd
Jul 15, 2008 9:23 am
Jim, in the windows explorer in the Python25 file section I see the following: at200pc.pyw 15KB Python File (no console) 15.07.2008 10:09 Maybe it...
3149
harle83
Jul 17, 2008 4:33 am
Thinking of buying a Yaesu FT950. I use a G5RV which according to Yaesu the 950 won't tune. Is there a cable for the AT 200Pro to tune the 950? Or will it not...
3150
jimahlstrom
Jul 18, 2008 4:44 pm
... I do not understand what you are saying. It sounds like you have Python 2.5 installed correctly. And it sounds like the file at200pc.pyw is somewhere on...
3151
ldgelectronics
Jul 18, 2008 6:47 pm
Harry, The AT-200Pro will work fine with your 950. While we do not have an interface cable for it, just use the Auto mode and it will tune when the SWR is...
3152
jadale55068
Jul 19, 2008 6:56 am
A set up my Z-11 Pro with a BetterRF Yaesu Tune Controller on a Yaesu FT-950. When I push the Tune button on the 950 the Z-11 Pro tunes OK. But when I tune off...
3153
Leonard K. Pennock
leonardpennock
Jul 19, 2008 1:25 pm
You don't say what kind of antenna or what band you are using; however, depending on the combination that isn't unusual behavior. My Hamsticks and UHV-6 on my...
