Chris I was wondering what the fitting at the base of your mast is? http://ph.groups.yahoo.com/group/JaguarYacht/photos/view/84bb?b=2 Is this for a mast...
As I sail the solent I was wondering if anyone has put a zinc anode on the lifting keel of thier Jaguar 22. I have anodes on my two small bildge plates....
... <snip> ... Mine is the same and I therefore assume it is designed that way. I have just converted my sail to sliders so I will have to find a way to...
Ken, I've uploaded a couple more images to the Yahoo Group Photo file under Aretia. You are correct with the stainless mast fitting in that it's an adaption to...
It's busy around here at this time of year isn't it? Does anyone know what the "correct" finish for the exterior hardwood is on a J27? The grab rails and the...
There is no specific correct finish. Varnished teak will need to be stripped back to the wood before applying another type of finish. On my old J25 I used...
Ken, I don't know if you remember, some time ago I mentioned a burnt out Jaguar 22 in the field next to my club and the brand new keel lying amongst the...
Upn Laurie's recommendation I used Deks Olje (Two parts, but you don't have to use No. 2 if you don't want). I was not disappointed. Expensive but very very...
Hi Ken, Mine has sliders and this makes it worse. It just drops down and out. I was hoping to put a lasy jack system in to help with single handed sailing ... ...
Yes, but my plan is to fit a removable pin which will fit through a pair of holes drilled at the base of the 'tight' slot. This will prevent the sliders from...
I went round to Hayling today. There IS a rather neglected J21 sitting there by the name of "By George 2" Adrian, I have emailed you details and pics. Colin...
Good morning, 'Lady J' is almost ready to take to the water but there is one job I have put off. I have several points where water is getting nto the cabin...
Bridget Lyons
bridget.lyons@...
Apr 3, 2007 9:12 am
662
Would anyone know where I can get a water pump complete for the above engine. ( at a reasonable cost ) ? The existing pump housing is worn internally and...
Exactly what I did on my 22. I used a split pin. Job done, Laurie _____ From: JaguarYacht@yahoogroups.com [mailto:JaguarYacht@yahoogroups.com] On Behalf Of Ken...
Laurence Milton
laurie@...
Apr 3, 2007 4:43 pm
664
For the 1st time in I don't know how many years, I have stripped all my deck wood, re coated (several) with Deks Olje 1 prior to several coats of 2. Lovely, &...
Laurence Milton
laurie@...
Apr 3, 2007 4:47 pm
665
Hi !, Not too sure if this is relevant . Last year I replaced all of the windows on my J25 . I kept the aluminium frames and replaced the rest . Cleaned the...
An anode near the winch attachment to the is no a bad idea, I did so on my 22. The bilge "plates" on the 22 were normally grp, & as such anodes thereon (there...
Laurence Milton
laurie@...
Apr 3, 2007 7:03 pm
667
The standard swept blade on the 27 would be considered high aspect as was, any more would be constrained by draft, & be deeper than the keel.? Or does Stefan...
Laurence Milton
laurie@...
Apr 3, 2007 7:12 pm
668
Volspec (Tollesbury) or Frenchs Marine, (Brightlingsea, Levington.) both on the east coast though, are 2 that I know of..... Laurie _____ From:...
Laurence Milton
laurie@...
Apr 3, 2007 8:02 pm
669
Hi, Its that time of year to get ready to go back on the water. I moved my boat last year and so had to derig my jag 25. About to get the mast back up and...
Bit of digging and I've solved my own problem ... well part of it anyway. Mast and boom is made by Isomat Sailspar.co.uk stock fittings for these in UK. the...
Thank you Kevin, will contact this company for the new seals before I start. Regards, Clive ... From: kevin.cullinane To: JaguarYacht@yahoogroups.com Sent:...
Bridget Lyons
bridget.lyons@...
Apr 4, 2007 2:45 pm
672
Yes, I believe the fitting you require was made by Isomat, who have 2 uk agents, one of which is Sailspar Limited in Brightlingsea - 01206 302679 or...
I think someone has already mentioned it: if so sorry to repeat things; but try Sailspar as listed in the recommended service/suppliers directory.. Laurie ...
Laurence Milton
laurie@...
Apr 5, 2007 3:49 pm
674
Has anyone practical experience of the effect of a drying mooring on antifouling. On my boat at Thornham, the mud seems to have stripped off the eroding...
I moor on a drying mud berth and in my experience get no marine growth whatsoever. A coat or two of aluminium paint to seal out water seems to work perfectly...
can you please email the info on removing lifting keel many thanks tony ... All New Yahoo! Mail – Tired of unwanted email come-ons? Let our SpamGuard protect...
I want to buy a new mainsail for my 1982 Jag 21. Does anyone out there know the right measurements( I don't think my present sail is the original), the name of...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
