My new designs for February are now on my website. As usual they include some combo packages at discounted prices. They are located on my New Designs page....
Check to ensure your table is level. I also recommend that you visit the APQS forum, many of the IQ/APQS owners can probably help you, especially Angela...
Valentine's Sale!30 Percent Off Hearts & FlowersFebruary 1 through 10 To celebrate Valentine's Day, we're offering all of our Hearts and Flowers designs at 30...
First rule of troubleshooting: SEND IN YOUR LOGS. You'd be amazed at what Zoltan can see just from logs. Another tidbit: if you will send your logs in right...
Did you try lowering the engagement strength on that motor after we talked on the phone? I found that my machine worked well even when I heard no growling...
Get down low and go between computerized mode and manual mode a few times to confirm the drive wheel is actually lowering down and raising back up. Do this for...
Dear Zoltan, Helen, Angela, and everyone else who helped me solve the obstruction issue, Linda Miller helped me remove my table roller bars and we tightened...
Oh my goodness Sandra, who is Linda Miller. I need her help, here in Phoenix, AZ. I'm getting the same message and I have tried lower/increasing engagement...
Renee, What kind of quilting machine do you have? Sandra From: IntelliQuilter@yahoogroups.com [mailto:IntelliQuilter@yahoogroups.com] On Behalf Of Renee Sent:...
Renee, You make me blush and laugh out loud!! I know how you must feel all alone, but we are here, really. Call me if you need me to talk you off that...
I haven't had a need to have my IQ measure a quilt for a while. I am now trying to put a panto inside borders. I measured the quilt manually, then decided...
I think a class on IQ maintenance would be great at MQX in the future. This explanation sounded Greek to me! ________________________________ From: Sandra...
Sandra's solution was specific to APQS machines. It involved tightening a bolt on the machine itself which helped the motor to be stable. There are two classes...
When you say that IQ was off by an inch, was that in comparison to the ruler you used or did the stitching stop an inch too short? Check the sensor wheels on...
Hi Helen, I cleaned the wheels, just in case. Just looked and they seem to be straight and turning. I haven't tried stitching yet. I know if I use the...
What I have been doing in case I need to adjust the height because of drawup of the quilting. I put a safety pin at the half-way point of quilt top before...
I was at one of my favorite stores Wednesday afternoon. Lites up a large area ofr quilt backing to see stitches, much better than my flashlight, and are on...
Are you sure you're measuring straight across with the IQ? A little bit of diagonal movement will cause your measurement to not match a tape measure. Cristyn...
Kathy, My IQ *always* measures differently than my metal tape measure. I don't worry about it anymore, and always go with the IQ measurement. I assume that...
I hope to be coherent. When beginning a new quilt and after having set up the design (wider than I truly need) and sequencing all rows, I clip left and rights...
Thanks everyone. Got brave and quilted the quilt today. Used the IQ measurements and had good luck. I didn't realize I could still use the IQ measure...
I do the same thing. I look at what is actually stitched and keep restarting until I am "right". Julie ... -- Julie M. [Non-text portions of this message have...
Thanks to Julie Karlak suggesting to use Clipping Block some time back. I have been doing pantos lately using Clipping Block for edge to edge quilting. I did a...
Pat picked up her Hungery Catapiliar quilt earlier today see link below: http://home-and-garden.webshots.com/photo/2460937370101906503RLtNsf Ann Bright's...
Oops --When I announced new designs a few days ago I misspelled the name of my website. It should be: http://www.quiltersniche.com . My excuse is that it was...
I put a test piece of fabric on my machine yesterday and set up a panto. It was only about 35 inches across. The first row stitched out fine, the second one...
Hi Liana, It sounds as if your Y motor isn't straight. I'm sending you some information privately. Helen ... Helen Baczynski mailto:helen2209@... North...
