I have some one who is going to go to Springfield, pick up my mill, and bring it to me here in Ga.. are there any particular spare parts i should ask him to...
83
kentfreeman@...
Sep 2, 2001 2:56 pm
Littlemachineshop has a spare parts kit (http://www.littlemachineshop.com/lms/products/product_category.php? category=895267850). Also almost a traffic on this...
84
Barry Young
barryjyoung@...
Sep 3, 2001 3:50 am
Your Grizzly will make much heavier cuts than your Sherline. It is like night and day. I no longer own a Sherline. Nuff said Barry Young ... ...
85
shindin@...
Sep 20, 2001 11:24 am
Glenn went to Springfield and picked up my mill, we are to meet saturday morning in Chattanooga, Tn to do a swap... he was to get me a 3/8" end mill holder,...
86
Barry Young
barryjyoung@...
Sep 20, 2001 10:41 pm
The 3/8 collet works fine in the mini-mill. Considering the light loads that will be placed on it, you can do just fine without an endmill holder. Yes, the...
88
shindin@...
Sep 25, 2001 10:39 am
i am considering the "baby" millling vise from grizzly, it's about $50, and funds are a bit tight after all the recent stuff i've picked up.....has anyone used...
89
shindin@...
Sep 27, 2001 12:46 pm
how far does the grizzly 2 1/2" vise open? it's the model g-9002, going for $49.95, has anyone had any experience with it? just wondering if i can plan to use...
90
wmiller45@...
Sep 27, 2001 9:26 pm
Hi Kent, Newbie here, didn't know this group existed. Been on the 7x10 site for a while. I ordered a REX mill (should have it in a couple of weeks), after ...
91
jtveazey@...
Sep 27, 2001 10:53 pm
Where does one find REX Minimill? Got a web address for them?...
92
brentwford@...
Sep 28, 2001 12:08 am
Thanks! This is the first time I've heard of anyone coming up with a real solution to the problem. Great job. It will make the mill 100% better to use as the...
93
Barry Young
barryjyoung@...
Sep 28, 2001 1:16 am
Outstanding! I am happy someone is doing quality mods to this basic tool. Does this person have a web site? Barry ... ...
94
wmiller45@...
Sep 28, 2001 4:50 am
... No, no website. He advertises in HSM everymonth though. If you want his phone #, email me off list (I don't receive emails from this list) and I'll send it...
95
kentfreeman@...
Sep 28, 2001 1:43 pm
Bill Thanks for the info. I would like to hear from you in the future on how you like your REX. I ended up corresponding with Rick a couple of times. I was...
96
wmiller45@...
Sep 28, 2001 2:06 pm
... on ... Quill feed would be nice, but then again so would a knee under the table, neither of which fit within my cost or space constraints. ;) The work I do...
97
wmiller45@...
Sep 28, 2001 2:15 pm
... motor that comes on the HF unit. It looks like the spindle bearings, being large enough to handle the R8 spindle, are more then large enough to handle a...
98
philteague@...
Sep 28, 2001 9:31 pm
Assuming that space is not a problem would a mill/drill been an option? It would certainly be more rigid than a Grizzly minimill and it would handle R-8 out of...
99
wmiller45@...
Sep 28, 2001 11:58 pm
I might be able to make room, but one of my requirements is that I be able to move the machine myself, which limits me to ~200 lbs. I'm getting old, and can't...
100
edbash@...
Oct 2, 2001 11:06 pm
hi group just received my mill today from micro mark today .the spindle is very hard to turn by hand. i ran it for 10 minutes in low gear it seemed ok.then i...
101
Chris Wood
chrisw@...
Oct 2, 2001 11:53 pm
Ed: Doesn't sound normal to me. Try a couple things: 1. Make sure the High/Low shifter is not all the way one way or the other, but just back from the stop....
102
wmiller45@...
Oct 3, 2001 12:20 am
I have not received my mill yet, but from lurking on the 7x10 list I can tell you that most over there recommend taking the thing apart and cleaning/oiling...
103
nkefalas@...
Oct 3, 2001 2:47 pm
Easy fix for you Ed Its your preload. Remove the cap where your draw bar goes on the top of the headstock. You will notice a round black finish "nut" that ...
104
edbash@...
Oct 3, 2001 10:30 pm
Thanks for all the help so far!! Well nick the problem is with the preload of the main bearings. I did do what you said ,actually took off the spanner nut ,no...
105
nkefalas@...
Oct 4, 2001 12:29 pm
OK Well here we go. You need to get the spindle loose. I would get a 2x4 and place it over the spindle, (lower the headstock all the way down for this !) and...
106
resourcemail10th@...
Oct 4, 2001 3:07 pm
No need for searching & researching for endless hours to find the best ways & tools for promoting your website, nor the need for endless hours of site link...
107
Chris Wood
chrisw@...
Oct 4, 2001 3:25 pm
WAIT!! Don't try to hammer the spindle out with the head on the mill. You will just bust stuff up! It ain't that simple. Now, giving the top of the spindle a...
108
tonyaprice@...
Oct 4, 2001 4:33 pm
Does any one here own one of the Micromark mini mills, Is the english lead screws worth the difference in price from Grizzly? Is their anyother differences in...
109
Barry Young
barryjyoung@...
Oct 4, 2001 5:10 pm
I agree Chris! I have had the same problem with my Jet lathe, but discovered the problem long after the warranty had expired. Unfortunately. If one must remove...
110
Barry Young
barryjyoung@...
Oct 4, 2001 5:11 pm
My Grizzly Mini-mill has inch pattern lead screws. Before you make assumptions, measure the actual travel with a travel indicator. 8 turns of the handwheel ...
111
Jim n Deb
epdc@...
Oct 4, 2001 5:27 pm
I'm hoping someone here can help me quickl.... I noticed considerable runout with my drill chuck in my Harbor Freight Mini Mill. Can I take the chuck apart...
112
nkefalas@...
Oct 4, 2001 6:19 pm
A couple of good raps won't do any harm. Especially if you lower the head all the way down to reduce bending modes to the column. The head takes more abuse...
