dds6263, I have had problems with mild steel on the unlocked axis when cutting back and forth (climb milling in the back direction to speed things up). I have...
Jerry, I expect that you are right. Also, it seems that Kayla's mod is untried and perhaps problematic. Oh well, if it ain't broke, don't fix it :-) JIm...
I am looking at the 3 axis shooting star from LSM or the 2 axis Accurite. Not sure I need the 3 axis as I already have the z taken care of. I see one...
I bought a 2-axis Shooting Star DRO for my Grizzly G4000 Lathe and very happy with the system. I will eventually put a DRO on my Grizzly Mini-mill also and my...
2470
h12721
73772.2557@...
Oct 2, 2003 4:35 pm
Hi, I am looking for the schematic diagram of the speed controller for the Homier Mill, 6 Months old. Not the wiring diagram. My problem is that when I turn...
2471
h12721
73772.2557@...
Oct 2, 2003 4:36 pm
Hi, I am looking for the schematic diagram of the speed controller. Not the wiring diagram. My problem is that when I turn the pot ccw and off, the slightest...
Hello MiniMillers ! Not sure if this is necessary, but here goes anyway. Been lurking for about five minutes; found the group while hunting for Barry Young. ...
Hilmar: Here's what the manufacturer says about the trimmers. Regards, Chris Wood LittleMachineShop.com <www.littlemachineshop.com> The premier source of parts...
Hilmar, when you say "will activate the motor", does this mean it will turn slowly and erratic? Mine does this. It is most likely caused by a dirty (or...
OMG!!! Hello there George. How have you been? It has been SO long since we last emailed. Business still OK? I was thinking of you and your metallograph just...
The only reason I know what nut you're talking about is that I just took my X-Y table apart. Anything I should know about getting this nut back in right ?...
Jim, Just my opinion, First I never make a cut without locking down the table that I'm not moving. Second, climb milling is not generally recommended, even on...
Jerry, Thanks for the advice. Experience is everything! I have also found this to be a pleasant way to get a little needed discipline around patience... Jim ...
Hi Leo, exactly,in my opinion,if in the ccw pos. the motor should not rotate . The motor sorte of jerks around. HM ... will ... by a ... controller. I...
Hi Leo, exactly,in my opinion,if in the ccw pos. the motor should not rotate . The motor sorte of jerks around. HM ... will ... by a ... controller. I...
Cletus, can you tell me if this DRO has tool offset for using an edge finder and if it will remember where you were at if turned off? Thanks Bob ... very...
Hilmar, the control is similar to an old fashion TV or radio volume control with a switch. These controls are notorious for getting "dirty". In volume control...
Leo et al, Ironically, I worked in two-way (public safety) for quite a while. On the light-weight portables, the best solution I found was a squirt of WD40...
... Not true. It resets the controller, if there is some shut-down event (like an overload). But, unlike that radio/tv switch, this one turns ON when the...
You wrote: "Not true. It resets the controller, if there is some shut-down event (like an overload). But, unlike that radio/tv switch, this one turns ON...
Hi Group! I made some comments about the speed control potentiometer and switch the were completely wrong! PLEASE DISREGARD THOSE STATEMENTS!!! The comments...
Hi, Leo and Richard and the rest of you,thank's for the advice and help,now the question remains: Should there be power on he motor if the pot switch is...
... It has been a while since I looked into this. My machines just keep on working, so I don't have much incentive to gather repair data! AFIK, there _may_ be...
Hi there: I do not know what kind it is. Just saw one go on ebay less than 3 months ago though. What a steal at $200. ... __________________________________ Do...
OK guys... let's get some straight answers here. 1. Has anyone had the (Griz Part #39 - fuselage seat) ground to correct the X axis tram? If so, did it correct...
