Hi! I just purchased a Hardinge Mill (Model UM) with a 20 X 6 inch table. Being new to machine work, can you direct me to: 1) How to best Clean the machine...
25
Jarzyna, David
djarzyna@...
Apr 4, 2001 2:40 pm
Subject: FW: found it! After years of sufing the web, I have finally found it! Click Here: <http://www.shibumi.org/eoti.htm>...
26
Dave Jarzyna
djarzyna@...
Apr 4, 2001 3:40 pm
ED- Best for now is to direct you to our "Brother Group" 7X10Minilithe http://www.egroups.com/list/7x10minilathe/ Granger is a source of Motors - yellow pages...
27
Joe Schulte
JSchulte38@...
Apr 4, 2001 7:33 pm
... some ... has ... and ... ED, Just a thought. We have here in northern N.J. a used machinery firm who are very active at model engine shows, clock shows and...
28
rralbers@...
Apr 5, 2001 7:05 am
... A phase convertor converts single phase to 3 phase. The motor that uses that 3 phase power doesn't matter, it just sees the 3 phase power. Your 2 speed 3...
29
rwilks@...
Apr 5, 2001 9:51 am
... with ... about ... Here is a phone number I found for Sobel Machine in NJ - it was listed on the Resource Page from the North Texas Metalworking Club :...
30
eabel78050@...
Apr 5, 2001 1:45 pm
Thank you for all the replies. My checking in with the NJ Sobel Brothers machine Co. yesterday indicated that they do not have either the "Overarm" nor the...
31
ben5002001@...
Apr 15, 2001 2:17 pm
... indicated ... support "Bracket" for ... those items ... way NOT to ... found ... and reset ... out of my ... someone has probably said this already, but...
32
tjo1221@...
Apr 30, 2001 11:18 pm
Has anyone received the new Harbor Freight 44991-OVGA mini mill? Tim...
33
Kirk Becnel
kirkbecnel@...
Apr 30, 2001 11:40 pm
I called today and they said it was backordered again. Last time it was shipped. It was supposed to ship tommorow. I will know then if it shipped or not. ... ...
34
Dave Jarzyna
djarzyna@...
May 4, 2001 4:26 pm
... I finally got around to creating the first installment of the mini- mill pages - similar to mini-lathe.com http://www.mini-lathe.com/mini_mill/index.htm...
35
Barry Young
barryjyoung@...
May 7, 2001 2:31 am
Hi Dave: I have been so incredibly busy with classes that I have been unable to even visit the minimill site. I went and looked at what is up there and I must...
36
Ed Abel
eabel78050@...
May 7, 2001 8:18 pm
Hi! Does anyone have a suggestion for a book, magazine, website which provides BASIC lathe and milling projects? I already subscribe to The Homeshop...
37
Barry Young
barryjyoung@...
May 8, 2001 4:17 pm
Hi Ed: Definitely Using the Small Lathe by L.C. Mason. Barry ... __________________________________________________ Do You Yahoo!? Yahoo! Auctions - buy the...
38
mschmalenberg@...
May 14, 2001 10:48 pm
Hello Barry I am new to this group I will be picking my mill up tomorrow. Did you change your spindle and if so who did you contact and how. Thank you Mike...
39
Barry Young
barryjyoung@...
May 15, 2001 1:36 pm
Hello Mike: I did not change the spindle. I found reasonable priced collets from one of the fellows on the minilathe group and so there was little point in ...
40
jtec@...
May 15, 2001 4:12 pm
... Finding more collets is a hassle. Is this a commercial source, do you have a URL?...
41
rralbers@...
May 15, 2001 6:16 pm
... Grizley has collets, for both 12mm and 3/8" drawbar. Also try Victor Machinery, url: http://www.victornet.com/cgi-bin/SoftCart.exe/cgi-bin/product.pl?U+scs...
42
Barry Young
barryjyoung@...
May 16, 2001 11:07 am
For collets, clamp kits and lots of usable information all specifically for the minimill and minilathe, check out...
43
tonyaprice@...
May 17, 2001 12:57 am
I placed my order for the Harbor Freight 44991 Mini-Mill on 4-1-01 because I really wanted the R-8 spindle taper. However, I am becoming very frustrated with...
44
Barry Young
barryjyoung@...
May 17, 2001 6:46 am
Hiya Tony: You will find that in addition to realistic delivery dates, Grizzly has excellent customer service. I had a bearing problem. The dust covers on the...
45
jtec@...
May 17, 2001 7:20 am
... IMO, an R8 spindle on these small, moderately powered mills is unnecessary. The main benefit of the R8 collet is less slippage under severe load, but that...
46
tonyaprice@...
May 18, 2001 4:39 pm
Hello Group, Well, I just contacted Harbor Freight and the ship date for the 44991 Min-Mill has again been moved out. HF now shows a proposed ship date of...
47
Robert Sigler
rsigler@...
May 19, 2001 8:56 pm
Agreed. I have had the exact same set of experienced from Harbor Freight as you describe. In recent months I have attempted to order 7 separate items. All...
48
jtec@...
May 23, 2001 2:35 pm
What vise is commonly used in the mini mill? I've seen some small scale units labeled 'machine vise' that might fit the table, but they don't seem to lock-up...
49
Barry Young
barryjyoung@...
May 23, 2001 11:28 pm
Howdy: I bought a tilting vise from Grizzly when I bought my mini-mill. I have not used it yet, but for $30 it was an absolute steal. I will use it for that...
50
jtec@...
May 24, 2001 12:14 am
... Which model, Barry, the ones I've seen appear too large for the table....
51
rsigler@...
May 24, 2001 11:39 pm
I use a 3" vise from Enco - part number 428-9127. It cost $59.99. It seems to be the perfect size from my perspective. It doesn't have a swivel base but it...
52
Barry Young
barryjyoung@...
May 25, 2001 1:26 pm
Hello. The tilting vise I bought from Grizzly is the $25 G8194. Yes, it is a little tall for the minimill, but as I said, I only use it for that odd job to...
53
afogassa@...
Jun 1, 2001 7:53 pm
... They ... - ... need ... Barry, I've a grizzly minimill retrofited to cnc and I realy like the idea of using R8.Would you post the link to Seig...
