Bruce, Will I followed your advice and I am afraid I get the same message 'Power SDR encountered a problem and needs to close'. Thanks anyway. Keith...
2853
Bruce Greenleaf KF1Z
bruce_greenl...
May 4, 2010 2:21 pm
Keith, Does the error box give an option to view the error? If so, maybe you can copy and paste the error details here, and may get some help that way to...
2854
xernz
May 4, 2010 5:35 pm
Hello All; Just some information… One of my PC a 3.2 Gig, 1 gig Men, single core does behave in a similar way but does not shut down. What happens is it runs...
2855
Bob
boblusby
May 4, 2010 8:55 pm
Deleted and re-installed the latest program. Same problem, actually worse now. No other programs running except whatever Windows normally has running....
2856
Bruce Greenleaf KF1Z
bruce_greenl...
May 4, 2010 9:10 pm
So the G40 and GSDR work fine? Bruce ... From: Bob To: GenesisRadio@yahoogroups.com Sent: Tuesday, May 04, 2010 4:53 PM Subject: [GenesisRadio] Re: Genesis 1.1...
2857
Ken Evans
w4du...
May 4, 2010 11:01 pm
I am finishing the phase 9 check out. I set the Delta 44 Mixer settings as best I could with interpretation of the instructions. I did not find a "wave in"...
2858
Bruce Greenleaf KF1Z
bruce_greenl...
May 4, 2010 11:32 pm
The output voltage setting is in GSDR. Under 'setup' 'audio' (soundcard settings menu) Right above the RX swap IQ box. don't use the test button. As for...
2859
Bruce Greenleaf KF1Z
bruce_greenl...
May 4, 2010 11:37 pm
Easier to measure the "wiper voltage" of R50T and R51T at the ends of R46T and R49T that are closest to the pots (maybe) :-) That way you may be able to...
2860
Bruce Greenleaf KF1Z
bruce_greenl...
May 4, 2010 11:39 pm
Also meant to meantion that the output voltage will be different for each soundcard... I found that with mine it ranged from .5v to 1.1 volts. Any less than .5...
2861
Gene
aimhightoday
May 5, 2010 4:45 am
I do not have any reception from BNC1 with antenna. Very little signal from signal gen at C1R using Oscope. Place antenna between junction of L9N and L10N and...
2862
keithharrisson
May 5, 2010 8:03 am
Hi, Regretfully no, that option is not offered. Would it help to put the .Net folder into the GSDR folder? Keith...
2863
keithharrisson
May 5, 2010 8:12 am
Hi Ern Thanks for your comments. I did have Power SDR installed at one time but I removed it a long time ago as I thought there might be a connection in view...
2864
Bruce Greenleaf KF1Z
bruce_greenl...
May 5, 2010 11:26 am
Yes, I have encountered such a problem.... ( I put a cap in the spot marked C10N* and I had on in C10N ) C10N* and C9N* do not get inserted. Check L9N for...
2865
Bruce Greenleaf KF1Z
bruce_greenl...
May 5, 2010 11:54 am
Keith, No, do not attempt to move .NET. Do you have different user accounts set up on your computer? What version of .NET framework did you install? Where do...
2866
Bruce Greenleaf KF1Z
bruce_greenl...
May 5, 2010 12:00 pm
Attached is a screenshot of the files that are in my GSDR folder. I think ALL but the Flash programmer, and the firmware file are needed. The wisdom file is...
2867
bruce_greenleaf_kf1z
bruce_greenl...
May 5, 2010 12:49 pm
Just a reminder..... Still, have: G59 GPA10 G3020 G80 and G40 Kits in stock and ready to ship. Sorry, still don't have my website online. So please use email...
2868
Gene Arnold
aimhightoday
May 5, 2010 4:13 pm
Bruce, The cap value for C10N is correct, 82pf (820). I noticed the empty spot above C10N. What value did you use? I have continuity from C4N to C1R. (.9...
2869
Bruce Greenleaf KF1Z
bruce_greenl...
May 5, 2010 4:29 pm
Gene, Are you only testing a particular band? I mean when you have the Ant connected to BNC. Do you have the AF or RF preamp on? or ATT? These settings COULD...
2870
Bob
boblusby
May 5, 2010 4:32 pm
The G40 ran good with Power SDR V1.9.0 sr40. Don't think I ran it with GSDR. My first G40 and G3020 are in Michigan. I have a second G40 here to build so it...
2871
Bruce Greenleaf KF1Z
bruce_greenl...
May 5, 2010 4:33 pm
Rereading your post... By the measurements given... I have to assume the RF-preamp is off... the AF pre-amp probably wouldn't have an effect... The ATT must be...
2872
Bruce Greenleaf KF1Z
bruce_greenl...
May 5, 2010 4:37 pm
Keep hitting SEND to quick.. :-) Gene, you can unplug the cable that goes to the band-pass filter relays... This will disable ALL the BPFs.... See if anything...
2873
Bruce Greenleaf KF1Z
bruce_greenl...
May 5, 2010 4:39 pm
Ok Bob, I'm not sure if the anti-virus software could impede GSDR.. I do know some of the other SDR programs I run here with other radios, that can be an...
2874
Gene Arnold
aimhightoday
May 5, 2010 5:08 pm
I have tried all bands with the RF-preamp on and off, also the same with the AF-preamp. I was on the 40M band when I received reception with the ant connect...
2875
Bruce Greenleaf KF1Z
bruce_greenl...
May 5, 2010 5:13 pm
No nothing goes in that empty spot (C10N*) Also nothing in C9N*. First, try either OUTSIDE the ham bands.. OR unplug the BPF connector... to be sure there...
2876
Bruce Greenleaf KF1Z
bruce_greenl...
May 5, 2010 5:20 pm
Also check the components in the input (BCB reject) filter... You could lift one end of L5N or L6N (easier) and try the antenna or generator there... If that...
2877
Gene Arnold
aimhightoday
May 5, 2010 10:02 pm
Bruce, The problem is fixed. C9N* should be empty. Some how I placed a 100nf Cap there. After removal I have signals. I did notice that when I enable the...
2878
Bruce Greenleaf KF1Z
bruce_greenl...
May 5, 2010 10:09 pm
Good! That's EXACTLY what I did, but with C10N* !! You have your connector to the wrong jack....? It is NOT the lowest one,,,,(one picture in assembly AND the...
2879
Gene Arnold
aimhightoday
May 6, 2010 12:05 am
Bruce, You are correct. The diagram is incorrect. I saw that and corrected my link this afternoon. I have it inserted in SV2PA next to the 4 pin plug. I...
2880
Bruce Greenleaf KF1Z
bruce_greenl...
May 6, 2010 12:20 am
Gene, The R1Z... I don't know! I will need to go look it up, and see what that's about. I missed it I guess. Did you install the jumper.. in KS1T? Next to the...
2881
Bruce Greenleaf KF1Z
bruce_greenl...
May 6, 2010 12:22 am
disregard my last.... :-) The KS1T is a ground connection for the soundcard in.... what am I thinking? bruce ... From: Gene Arnold To:...
