Hi Brian, Thanks for the info. I do hear some amount of echo even with the amplifier disconnected, however when connected it's really noticeable. I wonder if...
17072
Goran
yt7pwr2002
Mar 12, 2013 12:01 pm
Disconnect audio output from G11 input and connect headphones. Set TX IF shift to 0 and try Phone modes (set TX IF shift to 700 for CW test). This is transmit...
17073
Dalojan
pure_audio_kt88
Mar 12, 2013 3:21 pm
Hello Tim, I'm using a G11 serial number 140, use an ESI juli@ soundcard at 96kHz sample rate, 192kHz is not as good as 96 kHz due too increased noise. I also...
17074
kc8iir@...
kc8iir
Mar 12, 2013 4:02 pm
Goran, I sent photos to you, did the come through? Sent from my HTC One™ S on T-Mobile. America’s First Nationwide 4G Network. ... From: "Goran"...
17075
tom Pawlik
blbent
Mar 12, 2013 5:00 pm
Hi Ray, thanks for taking time out to my reply. I did measure the parallel pair of R6p and R7p and found at 2.7ohms. Other checks I found was the input...
17076
Goran
yt7pwr2002
Mar 12, 2013 5:08 pm
I did not receive any message yet. 73 yt7pwr...
17077
Carolyn Usher
kg6yum
Mar 12, 2013 6:44 pm
OK. I think I am getting the picture. I will have to pursue a different avenue. Thank you all for your reply. In regards to the post about "400-500 or...
17078
Ray Worrall
grimmerstreet
Mar 12, 2013 7:47 pm
Hi Tom,  I've had some success in removing small IC by flooding all the pins with solder on one side then placing a dental hook under one of the edge pins...
17079
Greg Johnson
kc8iir
Mar 13, 2013 12:00 am
I resent it, check your spam box. Is their a written instruction manual other than the online assembly manual.? I sent six pics, if you dont get them please...
17080
pure_audio_kt88
Mar 14, 2013 9:18 pm
I can change the text color of the buttons and safe the setup but after shutting down GenesisV2 and restarting again the text color is white. It seems that the...
17081
kc8iir
Mar 15, 2013 1:37 am
Instructions of build of multiband g11 bom add on kit seem a little mixed. what is the build order. do you build the 5 band rig and add the secondary board? i...
17082
Bruce KF1Z
bruce_greenl...
Mar 15, 2013 1:50 am
yes Do NOT install any BPF or LPF components skip pages 8 to 15 of the assembly manua;l part 1 From: kc8iir@... Sent: Thursday, March 14, 2013 9:37 PM ...
17083
Greg Johnson
kc8iir
Mar 15, 2013 9:52 am
Bruce, Goran helped me through a problem with firmware. He said to change the losc to 14.080. Where can this change be made. I know if you select the 20m band...
17084
Goran
yt7pwr2002
Mar 15, 2013 11:19 am
It is a bug in software. I fixed but won't be released until G6 work is complete. 73 yt7pwr...
17085
Goran
yt7pwr2002
Mar 15, 2013 11:49 am
LOSC can be changed by placing mouse pointer over digits (after few mS hovering over digits line is shown) and with mouse scroll wheel change desired...
17086
Dalojan
pure_audio_kt88
Mar 15, 2013 10:02 pm
Hallo Goran, I hope I can afford a G6 , I'm looking out for it to come. Dalojan dalojan@......
17087
rallen80
Mar 16, 2013 7:22 am
Hi just ordered a g11 and before I get it I thought I better make sure I have the right sound card I have a hp 2000 laptop from walmart witch iam guessing...
17088
begr12
Mar 16, 2013 11:41 am
Are these actual db eg if I go down from 48 to 45 will the output go up from 5w to 10w. i am only getting about plus or minus 1w if I go from 60 to 30. Thanks ...
17089
drooster1954
Mar 16, 2013 2:12 pm
Hi Bob, I don't recommend the Creative EMU-2404 external USB sound card that I and a lot of other members have. With my Window 7 64 bit desktop I can only set...
17090
Rom - K8ZU
k8zu_mi
Mar 16, 2013 5:24 pm
Hello Bob, I have a Sound Blaster X-Fi Xtreme Audio and it works great for me. The Noise level is low and it gives me the 9600KHz Bandwidth with the GSDR...
17091
zitko
zitkoi
Mar 16, 2013 5:42 pm
same with my G11 strange behavior - maximum out is on 48 not 30.?! soundcard voltage is 0,5 V - max output is on 15m 7W and lower band 5W win7 x86. Ivica 9a6cw...
17092
Tim
tahrens301
Mar 16, 2013 6:05 pm
Hi Rom, Do you have any echo (undesired), ker-tink when u let up off the key, un desired burst of carrier when u key down (both in ssb & cw)? Do you run an...
17093
Tom
tflynn6693
Mar 16, 2013 6:19 pm
I have downloaded GDSR to an XP machine. updated GDSR and tried to run it, the GDSR screen comes up and the software begins initializing. When I hit the...
17094
Hank
hank_kls65
Mar 17, 2013 2:14 am
Bob, If you want an internal sound card, get the Asus Xonar Essence STX. It is a very good card and you will see posts recommending it. It is not the cheapest...
17095
Frank Eichel
tmbrjnkr
Mar 17, 2013 2:53 am
I am running the E-MU 0204 quite happily on my Intel core i7 laptop (Asus N82J series) at 192 kHz wide using the Windows 7 WASAPI driver, with no problems. I...
17096
Dalojan
pure_audio_kt88
Mar 17, 2013 9:04 am
Hank, Can you give any information about where I can find schematics and so on about the ARRL 50Watt amp. Maybe it can be used in front of the output filters...
17097
Dalojan
pure_audio_kt88
Mar 17, 2013 9:10 am
I'm using an ESI Juli@ soundcard on Windows 7 64 bit and the 64 bit software for the radio. This sound card can doe 192 KHz sample rate but the noise is less...
17098
ivica_9a6cw
Mar 17, 2013 12:25 pm
if anybody has solved small issue with cpu monitor in gsdr ? after v16122012 not working. G11 - Win7 x86...
17099
Bruce KF1Z
bruce_greenl...
Mar 17, 2013 1:04 pm
please look back in the recent messages. link to information posted within last two weeks From: ivica_9a6cw Sent: Sunday, March 17, 2013 8:25 AM To:...
17100
ivica_9a6cw
Mar 17, 2013 2:41 pm
tnx Bruce but command lodctr /R not solved issue with cpu monitor on my laptop. was also another problem: swr warning although swr is ok. Today, I tried to run...
