The FT100 Group averages around 150-200 messages per month. Because the volume of messages is rather large, I would like to remind everyone of a few...
FT100@yahoogroups.com
Jun 1, 2008 10:11 am
30468
Dear Sir I am a radio amateur from Calcutta, India and I have been owning a FT100D radio since 2001. Yesterday there was a local thunderstorm in my area and...
... I had a similar problem once, radio would not xmit, although the red xmit light did come on, just no output. A reset did cure the problem. -- Alex / AB2RC ...
The TX red LED does not come on. In other words it is not a lack of RF but the radio cannot be switched to TX mode. I have tried a CPU reset withoug success. ...
Ha, Unfortunately the main processor is damaged (the TX pins are "floating"). The data jack of the FT-100(D) directly (non opto-isolated) join in the main...
My 100 dose not show transmit on the hand mic. But it does transmit OK.If you use the buttons on the mic the red transmit does work. Was wondering why the...
Ensure the positve supply termination is electrically away from the starter motor terminals and ensure the earthing is sound normally to the vehicle chasis as...
Have been using my ft100D as a shack receiver for the last few months , Last night I decided to check it out for transmit power , ( On a dummy load) result no...
Hi Art, Is the problem manifesting on ALL bands, i.e. HF/6m, 2m & 70cm? 73....Eric VK2VE. _____ From: FT100@yahoogroups.com [mailto:FT100@yahoogroups.com] On...
Hi Nilanjan, That happenned to me too with one of my FT100Ds. I simply perfromed a full reset and it worked again. Hope that works. I also modded...
Hi... Does it display OFF when you transmit? Check menu option 61 for the antenna setting. Maybe toggle it around through the ATAS settings... That often...
I'm rather confident you checked the band settings, but it's not uncommon for a rig that has been used mainly for reception to be left in a non-ham band...
I used one of the mounting points on the side of the radio for attaching the mobile bracket. My FT100 doesn't have the lug on the back of the radio either. ...
Neither do either of mine but the mounting bolts for the mobile brackets screw straight into the main chassis so I have used one of those, like Grant. ...
I've done two things that each have worked: 1. Ground the paint down to bare metal on the mounting bracket and use the screw attachment to the mounting bracket...
Name here is Ray n1plc,This is my first post.I read messages daily.I have a strange problem with my ft 100, it installed in my vehicle. for mobile. while van...
I have an early version of the FT100,(not the FT100D). I removed one of the screws holding the fan in place,inserted a lug and soldered a short green earthwire...
My guess is a spurious output that is voltage related. Possibly caused by poor grounding in the radio. I would remove the covers and check all screws are tight...
There is an add on eham for an FT 100 d and FC 20 Auto tuner if anyone is interested you should take a look. Joe ... No virus found in this outgoing message. ...
Can't offer any guarantee Ray, but have you tried the "Reset" procedure in the manual? I noticed a strange problem over the weekend, my 2M and 440 receive...
I spoke with Ray, his power was at 100% once he cut it back a bit the spurious emissions dropped and his swr sensor was okay. 73 de N1QXV John ... From: Robert...
N1QXV
N1QXV@...
Jun 10, 2008 3:16 pm
30491
Hello all, I'm new to the group. I have coming a FT100 that is suppose to have blown SRF7043. I'm really not sure about the HF side, will find out everything...
Hi Louie, I have replaced my V/U final with teh MRF1570 with total success. the only modification I had to do was grinding the mounting slots so that it...
In a message dated 6/12/2008 12:41:08 P.M. Pacific Daylight Time, ewinde@... writes: And whom do I contact to acquire the MRF1570? Eric WB4QOV ... You...
First I am new to the group but it looks like a great source of info. Thanks in advance for any advice you can provide. Just bought a used FT-100D and it will...
My receive audio is not working on 2M. HF, UHF and even weather on 162.550 all come in fine. But when I push the band selector to 2M, there is no audio -...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
