The FT100 Group averages around 150-200 messages per month. Because the volume of messages is rather large, I would like to remind everyone of a few...
FT100@yahoogroups.com
Oct 1, 2007 8:56 am
29480
Communication between the head (display unit) and the body (control unit) is via pins 5 and 6 of the head to body connector. Pin 8 of the 78P054 (Q6012)...
Whoops .. slight error in my previous posting; memory is fallible... Baud rate between control board and display micros is 57.6Kb. The NEC 784038 micro on...
That's not an easy job. I wouldn't do something like cutting off the RJ45 plug. Build an adaptor cable so you can retrofit if it doesn't work. Heil had an...
What I did was quite simple to do. I bought a modular to 8 pin yaesu adapter cable from AES and that took of the adaptabilty problem for me. Pretty simple...
Eric.... I made up my own adapter because I'm too cheap to buy one! In fact,I made up 2,one for my Knwd 950SDX and the other for my FT-100D, to use with a...
Occasionally, my FT-100 will turn itself on. This started happening when it was installed as a mobile, but now happens in installed in the shack. Thre isn't...
There is a timer for timed turn off , but I don't think I have heard of your problem of turning it's self on. Jock A Soutar KC6IIH / WPXX733 Barstow Amateur...
If you want to hear the audio coming from the rig to the PC, tap into the external speaker jack with a speaker...I would suggest using a shielded speaker with...
I just took my FT-100D out of storage. I hooked up the power supply and nothing, I haave good voltage all the way to the radio. Any ideas? and where can I send...
Yaesu will suggest Burghardt.com, since they no longer repair them. Did you remove & reseat the Control Head? Did you verify power on the main board? 73 Ron...
Greetings. I'm finally getting around to investigating various control programs for the two FT-100D transceivers I have. So far, I have looked to FTBCAT,...
Hi Mark, If you're thinking about using the CAT interface to load the memories, forget it, it can't be done. Unfortunately Yaesu never included ANY means to...
... Yep. I'm well aware of that. Although there is the poor man's memory writer. You use the control program to load the VFO and then push the couple of...
I looking for an ATAS 120(prefered) or a small screwdriver antenna, that will cover 40 thru 6 meters for my mobile with FT100. Trdae, or buy. Tks Jim N5DC/7...
Hi all. New member of this group, and new FT-100 owner. I just got it setup last evening. Had my 1st QSO's and all was fine. I like this rig! Then this...
The on/off switch is not a full on/off switch. There is still some power to the rig even when off. 1. leave the Astron on (this mimics a battery) 2. put a...
I have a Yaesu FT-100D, (used mostly for digital modes), but occassionally ssb phone which is in need of repair. Symptoms are as follows: CW output @ 100 W...
Tnx, Dan In trying to diagnose this, I took another look at the Astron, and saw that when I turned the switch on, the voltage spiked for a brief part of a...
Check all pc board mounting screws are tight and all interconnections are seated correctly, especially coaxial ones. Sounds like the spurious problem suffered...
New to the group. Has anyone located a good IF point in the FT100D to use as input to a band scope like the SDR-IQ? What are the IF freqs of the FT100D when...
I just found out the rig(FT-100D)i purchased has a dead hf receive, apparantly the front end was overloaded, and of course cant get parts ... so i have a...
well that depends on a few things doesnt it .... has it been modified in any way ?? ... is it low output on hf or the whole rig ?? i paid under $300 for the...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
