The FT100 Group averages around 150-200 messages per month. Because the volume of messages is rather large, I would like to remind everyone of a few...
FT100@yahoogroups.com
Nov 1, 2006 3:13 pm
28214
I wouldn't bother. Go to www.ebay.de do a search on ct-62. Do the math Get the cheapest on USB. Tell'm I send you. 73 Ed PE5ED...
Hi All. Thanks for the bidding on my FT body. I was surprised at what it went for. Anyway. I have listed a FT-100D serial number 11250008. I have also listed a...
Hi all,i have a 100d,it has just stopped working,it has power on 6m,but nowhere else,hf and 2-70 have lost all power,all else is ok,any idears would be...
2 and 440 may be the finals if so your out of luck ..... Hi all,i have a 100d,it has just stopped working,it has power on 6m,but nowhere else,hf and 2-70 have...
Steve, you may still find substitutes out there...here is a past email re: the finals...many more about this subject Jeff N2JQR Clint, Have you looked at the...
This is from a previous post. I had the same problem also. Make sure you a very good ground and the connections are clean. KB9YPV. Re: FT-100D power dropping...
Hi Mark, I had the exact same problem with my FT-100D (2002 manufacture). The problem was bad soldering on the output lead if the PA driver MOSFET. The bad...
Hi All, The removable connector on the FT-100 side is toast. Does anyone know what kind of connector that I should ask for to replace it? Thanks in advance. ...
Here you go Joe, a link to Powerwerx.com. http://www.powerwerx.com/category.asp?CtgID=1003 It might be better to just buy the complete cable. Al, n7ioh ... ...
Have you thought of ditching the Yaesu connectors and using Anderson Powerpoles? 73 de Peter - G0FIM / AA3JN ... From: n7ioh To: FT100@yahoogroups.com Sent:...
Gents, I only recently started tuning around 80 and 75 and I noticed that the up - down buttons don't "remember" 75M band. The next band below 40m is 80m and...
Yes Marvin it is still active. You may review the number of posting for each past month on the home page. I also suggest that you read the archive to stay...
I have an FT100, not the D version, that all of a sudden lost audio out of speaker and headphone jack during field day. Data output port still works though so...
The Programmable Memory Scan seems like a nice way to check out an unfamiliar chunk of spectrum. But on my FT100D I can't seem to figure out how to get ...
I have my second FT100D transmitting on vhf/uhf again. The first one was resoldering the driver output under the transformer that I saw suggested in this...
... The first thing I would do is check that the power levels have not been turned to zero in the menu settings. -- Alex / AB2RC Running a Linux/Mac...
In a message dated 11/11/2006 11:17:59 P.M. Pacific Standard Time, n5jep@... writes: I have an FT100, not the D version, that all of a sudden lost audio...
My FT100 is out of the car, so I can't test it here. But, did you press the VFO/MR button to put you in VFO mode? I don't know if the operating mode makes a...
You bet! Only most of us are busy using our rigs. Mostly read the mail and only comment when we have some meaningful contribution to the cause. Also you should...
Hi All! I have an FC-30 autotuner with control cable for sale. Works with Yaesu FT-817, FT-857, FT-897, FT-100 and any other Yaesu products with the control...
Try N1EQ in Maine. I have spoken with him on the phone and he does seem familar with working on the FT100D. He gets excellent review on eham.net. You can...
Make sure squelch is on, a little pass the treshhold. stan ... _________________________________________________________________ Stay in touch with old friends...
hi i have done mod and tune f52 fm freq on 10m 2m are now spot on, but 70cms is still about 10khz off freq but when i tern the power down the freq comes back...
i have done this mode and yes my fm is of frequency it is 8 khz on 70 cms and 2m is allso some khz off i will try setting up countor and ajusting f52 to see...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
