its not a 7700 but its close ! I have for sale: FRG-8800 with original box and manual the FRV-8800 internal VHF converter installed (box included) the FRA-7700...
... many ... i'm ... should ... the ... out of ... from ... advice ... from ... sangean ... frg ... still ... to ... is ... Hi have connected some nickle...
I think this farewell will be of interest to y'all. WP4IDK From: aimo ruoho Subject: Re: File - Farewell from the FRG-7700 Yahoo group! To: FRG-7700 Moderator...
I wonder where the spirit of Listing to HF radio is going Why do people keep asking ...What Antenna Should I use .....Whats wrong with EXPERIMENTING First...
... people keep asking ...What Antenna Should I use .....Whats wrong with EXPERIMENTING First as no two locations are the same or are you just to lazy to work...
I recently picked up an FRG-7700 and thought it was working, it is not. The tuning and display seems to work, lots of noise from the speaker but no S meter...
Hi Dick Some questions? Do you have the operating manual for the Rx? Do you have experience of HF Rx's? Can I assume that you have attached some form of...
In a message dated 5/11/2008 7:05:55 AM Eastern Daylight Time, g4gvw@... writes: Some questions? Do you have the operating manual for the Rx? Yes Do you...
I am most grateful to this group and in particular to Mr. Penders and Pat G4GVW for their help in getting my Yaesu Frg 7700 fixed a couple of years ago. I have...
hi group i got a query can i use a g5rv shaped like a (square)loopand connect to my frg 7700 i reckon i could maybe squeeze a full g5 into the loft ,i know you...
... YES Alan,...It will be used to Receive only, no problem. I took some plain electrical wire and made a square loop with many winds around, then ty-wraped...
Hello, Could someone please tell me why a Vacuum Tube Volt Meter (VTVM) is required for servicing a FRG-7700 as opposed to a modern day (in my case, analogue)...
the higher input impedance or the vtvm disrupts the circuit under test less than a meter with lower input impedance. if your meter has a very high input ...
Lee: The VTVM has a very high input impedance and will tend to not load the circuit under test as would a VOM. Today's digital multimeters usually have high...
Hi Froggers: I have many digital meters here including Beckman, Fluke and Honeywell but none of them are great for circuit tuning. Even if the digital meter...
Hi guys - I agree that you cant beat an analog meter for on the fly adjustments like peaking etc but I have a couple of Fluke digital meters and have serviced...
Yep a good digital meter also has a very high input impedance, and therefore low circuit loading. Up in the meg ohms which is way good enough. Mike ... the...
Hi Lee, Unless your "modern day analogue multimeter" is of a type containing solid-state circuitry equivalent to a VTVM it will not have a high enough input...
Thank You Very Much to everyone for the very fast replies to my question. I really should know these things but then I've only been a licensed ham for 24 years...
i bought mine about the same time,one thing i did a couple years ago was make a list of all the electrolytic caps in it, and replaced them with a better ...
Hi Froggers: Just because the sunspots are low doesn't mean you can't play with radios....I've been spending some time using my signal generator and frg7700 to...
HI to all wise men! I have a problem with my 7700 and I'm not able to understain the solution. Since a pair or years after I turn on my receiver also if I...
I also have problems with my VFO my FRG: mine stops at a little over 650 Khz while a tower VFO must make 1 Mega! I will go to realign by a specialist! If you...
J'ai aussi des problèmes avec mon VFO de mon FRG : le mien s'arrete à un peu plus de 650 Khz alors qu'un tour de VFO doit faire 1 Méga !!! Je vais donc...
... the ... Hi , Ok there are two adjustments on the Big center tunning knob, the inner one is silver color, the outer one is the Gray knob. Try adjusting the...
Just in case you don't have this famous information, it could help too. http://www.securesystemsnw.com/ft/ft-library/FRG7700-FRG7- FRG9600/FRG7700sg2.pdf mike...
If your VFO stops at 650 khz, the fault is not the VFO, but the first PLL. Download the FRG-7700 Survival Guide on the FoxTango site, there is a full...
