Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the FM900 group. File : /chips_test.xls ...
FM900@yahoogroups.com
Feb 2, 2007 10:46 am
6000
Thanks, always useful info for those that burn EPROMs. Barry ... From: FM900@yahoogroups.com [mailto:FM900@yahoogroups.com] Sent: Friday, 2 February 2007 9:44...
hi all just wondering can you program a fm 900 ot operate at half power and if so can you program it so that one of the buttons un the front dose this manualy...
... Hi Bruce. The FM91 can set the power (1, 5, 25W) from the front panel, the FM92 can't. The FM92 can be set though on a channel-by-channel basis for low ...
Have converted one FM92E to 6 meters with no problems, to check my documentation I thought that i would convert another one; What a stuff up.... But i have...
There are two answers to this problem. The first is to add or subtract 10.7 MHz to the Rx freq only. The Tx freq is not adjusted. You add or subtract...
I agree with Ron, those codes should work. I believe they were listed in the earlier FM900 manuals (back when 10.7MHz IF was the norm.). The only trouble you...
... you use FPP to generate a ".bin" file you then use that ".bin" file with your eprom programmer's software to burn the image to the eprom you do have an...
Hello to all, I am attempting to get operational an FM900 Eprom Programmer which has been donated to the Summerland Amateur Radio Club (SARC) in northern NSW. ...
Hi Geoff, I'm not at all familiar with this programmer, but have noted that some serial programmers rely heavily on the PC for their timing and that some don't...
On Tue, 27 Feb 2007 19:52:18 +1100 (EST), "Dave Horsfall" <dave@...> said: snip ... I'll bet you do too :) James -- http://www.fastmail.fm - The way...
Hi all, I am trying to get a TT3 going with my FM92. Works fine with an 828 but the Tx audio is way down with the TT3 and FM92. I have made the mod to R354...
Yes I do have a eprom programer. Maybe I should refraze the question. How do you create the bin file, because when I open the fpp program it comes up with a...
Hi Gordon, Looking at the TT3 circuit, you should probably either remove R8 from the TT, or feed the TT Audio out to the FM900 microphone input via a capacitor...
Hi needfm92info, Do you mean you've got as far as the entry screen for the Hardware and software codes, or not even that far???? What you put in the hardware...
I had the same problem when programming an FM93. Ofter fitting the eprom the radio half turned on with the display working but the relay on the RF board was...
HI all The FM900 in my wifes car sometimes leaves the squelsh open after receiving a signal, it just seems that it is set too light, even with the mute turned...
Just been working on the same matter - in fact just completed and tested it today (well yesterday now). As Mark suggests you may have a problem with the way...
Hi Paul, Judging from previous posts on this subject, it looks like the Mute Calibrate trimmer R250 (located on the receiver board) may need adjustment. But...
Further to my last post on this topic, I have just added to the files section details of an FM92 to Tiny Trak3 APRS interface that I have just completed. This...
Hi Gordon, Yes, as it is, the TT will not supply enough audio level. The solution is fairly simple, though. I have about 100 FM92's I look after with about 30...
I would like to thank Mark, Marcus and Ron, what a wealth of information you guys have. I have had the TT3 working ok today. Mark and Marcus, I am able to get...
Hey guys, I am new to this group and just have bought a FM91 it seems to work fine but it has a red dot in the right hand side of the display when TX. I know...
Hi Gordon, Yes, as it is, the TT will not supply enough audio level. The solution is fairly simple, though. I have about 100 FM92's I look after with about 30...
Hi all My name is simon,I recently bought myself a FM92 (off Ebay,where else?) and I am having some trouble with the VCO I belive. when I go to TX the thing...
I believe you have accurately described the problem as TX power out of range. From a fading with time memory, I recall that the forward tx power is measured by...
Here is a copy of my reply to suggestions made to me back in August 2006. If you search the archives of the group you will find other suggestions. This...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
