Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the FM900 group. File : /FM92 tx af...
FM900@yahoogroups.com
Dec 1, 2005 9:34 pm
5243
FM900: Group Rules Note: <this message is sent once a month to all members> 1. No spam 2. No Flames 3. No cross posts, especially non FM900 related 4. Try to...
FM900@yahoogroups.com
Dec 1, 2005 10:26 pm
5244
... I tried this tonight and it works very well indeed! The radio can't even be switched off from the power switch... just comes back to life again :-) When...
i'm after a head and mic for my 92R, don't require bracket but do need mounting blocks that screw onto head. does anyone have any spares at a reasonable cost?...
Sorry for the wide cross posting, but this situation has got to stop! Yet again I'm being flooded with requests for programming lead diagrams. This time the...
Hi all. I have the instructions for FM91 4 Bank conversion, and am wondering if it will work for an FM92. Which channels do you program the economiser to? What...
Mark Hooper
mhooper@...
Dec 7, 2005 6:38 am
5249
Hi Mark, The bank conversion should work on all the 900 series if you are using an external switch. Program any channels you like for economiser - it just uses...
Gidday All, I am catching up with a few months of emails to these groups and have the the simple solution to permanently power a FM900 so it can be left at a...
Sounds like a simple enough method. Does it work through a brown-out as well? Mark vk3byy ... From: FM900@yahoogroups.com [mailto:FM900@yahoogroups.com] On...
... Does anyone reckon this would over-ride the power off timer after 8 hours? (must try that, but it's a long wait!) Ta John IRLP node 6527 EchoIRLP node...
I've never noticed than one - I'm sure I've got FM92's that run all day and night without shutting down. Perhaps it only applies when economiser mode is...
... Dunno ..... it's an oddball one I use at home, and have never pulled the eeprom to see what's programmed, not that I have a means of doing that anyway! The...
Hi all. I have recently had a discussion with the other Mark H regarding a programming problem with FPP. When I use the FM93.bin file with FPP the eprom does...
Mark Hooper
mhooper@...
Dec 19, 2005 5:03 am
5256
The 8 hour timer is one of the programming options in fpp. Barry ... From: FM900@yahoogroups.com [mailto:FM900@yahoogroups.com] On Behalf Of John in Coffs ...
Hi Barry, Quite correct . The eight hour timer is to prevent vehicle radios using the vehicle battery and consequently causing it to become discharged...
Mine has run for weeks in the shed unattended. Shaun ... From: "Mark Harrison" <jmh@...> To: <FM900@yahoogroups.com> Sent: Monday, December 19, 2005...
Hi Mark, perhaps you'd better describe the complete process you are using to create and burn the EPROM, and the type of programmer hardware. There are a lot...
The programmer and FPP work fine for FM92. The eprom being burnt checks out fine for $FF's prior to programming I can read the file on the old Eprom The number...
Mark Hooper
mhooper@...
Dec 20, 2005 5:34 am
5261
Hmmmm, tricky! It sounds like the programmer is trying to program one or more locations twice (due to address wrap around). Does it tell you where the errors...
Hi Mark if you are using the Hacked "Out of Band" FM900 FPP Version 3. 0 The FM93 will not work it's Just the Way the FPP was Hacked for out Of Band. You will...
That is it. Changed to the original version of FPP and all is ok. Thanks to all for your input. Mark ... From: FM900@yahoogroups.com...
Mark Hooper
mhooper@...
Dec 22, 2005 12:04 am
5264
G'day all, I am trying to do my part to help out, and hence would like to tell you about this site. I am in no way affiliated with this site, but just think it...
Looks like a bloody good thing. Stick one up Ebay. I went through the whole routine to get a password and userID but now I can't get past the Logon Screen....
... Hi Richard I've had similar problems and I log off and go out of ebay and back in and log on and that seems to work. ... Ulf ... [Non-text portions of this...
Hi guys happy new year and all that! I have swapped the the new non functioning willem programmer for an old Jed Programmer. I have got the driver loaded and...
FM900: Group Rules Note: <this message is sent once a month to all members> 1. No spam 2. No Flames 3. No cross posts, especially non FM900 related 4. Try to...
FM900@yahoogroups.com
Jan 2, 2006 4:32 pm
5269
The bin files need to be located in the directory of your jed programmer, mine is in c:\pp and works fine. Cheers Mark H. ... From: FM900@yahoogroups.com...
Mark Hooper
mhooper@...
Jan 2, 2006 10:00 pm
5270
Presumably that would be for a UHF CB version? The seller should be very very happy! I think there are much more reliable UHF radios around for that ...
Hi Mark well I tried what you said I think, as i'm a apple computer type person and these windows machines well I wont go into what i think of them lol. I have...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
