FM900: Group Rules Note:<this message is sent once a month to all members> 1. No spam 2. No Flames 3. No cross posts, especially non FM900 related 4. Try to...
FM900@yahoogroups.com
Feb 1, 2005 9:35 pm
4803
Hey can you and if you can burn a 91 eprom for me,what would it cost.I would like to have the following programming done; 1st bank usual uhf cb 1-40 41-48...
Hi I have got hold of a FM92 W2 already converted to 70cm amateur band. It has some simplex freqs on 440mhz. Want to do a new eprom with the repeaters on...
Hi, I was wondering if someone can tell me what type of EPROMs can be used in the FM900/92. I have a bunch of recycled ones here which I can use, but I dont...
what isyour call cign?mat ... From: matt_hyne <matt@...> To: <FM900@yahoogroups.com> Sent: Wednesday, February 09, 2005 5:21 PM Subject: [Fm900] What...
Alexander Mill
kangaroo_sydney@...
Feb 9, 2005 6:30 am
4807
Hi Matt, I am going completely from memory as I am a little away from home at the moment seeing as home is in Sydney and I am in Malaysia at the moment. The...
... Yes is is. ... No, The set will need to have its vco & frount end adjusted to the CB band. There are manuals online that will explane how if you wish to do...
Wayne, Thanks for your reply.. I've since downloaded the fm91 service manual, and took a look inside. The VCO has written 'U/W1' under band against it. To me...
Hi Wayne, A W2 to 70cm? That's a big shift in frequency! Wonder if they replaced modules or rewound all the coils? I'm guessing a bit here, but some versions...
Hi Mark Not knowing much about these rigs, I looked in at the VCO and the slugs are not all the way in or out, so dont know if they have been redone. Will get...
I have just picked up an FM-92 as above ex Victoria. But have no knowledge of the channel setting or the Aux, scan settings if fitted. Can some please Guide me...
Unfortunately I'm In Qld but thanks Advance Amateur Radio Around the World. Seek your Local Radio Club and enjoy a lifetime of fun. Regards Bob M. VK4HAY ...
I'm in bundabergThanks Advance Amateur Radio Around the World. Seek your Local Radio Club and enjoy a lifetime of fun. Regards Bob M. VK4HAY Remove the Spam...
I am new to the list. Have a FM92 E which I am in the process of converting to 6m. One of the articles I have refers to stubs on the front end receiver coils ...
Eric, Don't read too much into it. I looked at all those little coils and decided it was too hard too add the turns, so I crushed up a bunch of ferrite slugs...
I have not been able to access diagrams from the "Files" area. one link wants me to sign up for a website. the "manual" has files I can not yet read .a01 etc? ...
Eric, a01, a02... (there should be a .arj file too) are in ARJ format (a type of file compression, like zip, used for multi part files) you can open them with...
Hello I got a couple of Fm92s here. Have the original Philips mics. I have 1 scan group. When i put the mic on the hanger, it doesnt set off the reed switch...
I have a similar problem and am trying to earth out the switch. I am unsure at what point on the PCB to take the Eath wire to?? Advance Amateur Radio Around...
Hi Bob All i did with the switch was to solder a wire accross the switch and that fixed the problem when you put it into scan it works strait away "Bob M."...
Hi Eric, Pleased to see someone else has taken the challenge, though not something I'd recommend to anyone :-) Yes, they do use helical resonators, though they...
I agree that shorting out the switch is a quick fix and works well so long as you don't want to use SELCALL or have the radio stop scanning when you pick up...
Yes Mark, you have covered it well. A new magnet is a quick and easy solution. The mercury switch idea is not bad either. Earthing the clip, definitely not for...
I have an FM92 E band radio I would like to get onto 6m but I need an eprom and control head/microphone for it. Where would I get an eprom? Anyone have a...
Hi But that wont give you ctcss encode. Need to disable cradle to get encode to work. UHF repeaters here use a ctcss tone for access Wayne ... From: yepiyepi...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
