Hi Add my vote to the YES. BUT, My contention is that we should make them into Activity & Education events (like Townsville, where there may be a couple of fox...
Some time ago there was a preamp for fm900 that I saw on a web page .....the preamp board was fitted to the rx board ( a very flat setup ) can anyone send the...
Folks, I have not played with one of these units for years, and just found this list. Basically, I am looking to pick up an A band version of a FM92 (remote ...
Hi All Matt Try the Files are here http://groups.yahoo.com/group/FM900/files/ you find all the info you need inc Software Also check the links section for the...
Hi all, new to the group, have looked at archives but no luck. If covered, pls forgive. While in listening mode, my unit (uhf cb + extras)seems to open squelch...
Hi Ken, Does the problem appear on all channels or just a few? I have had a few B band (132-153 MHz) Fm92 Mk2 models that have something like you describe on a...
Hi All, I have a VHF marine BIN file that has all the VHF marine frequencies loaded, I set one up a few month ago to get a 92 on VHF marine. I can e-mail the...
Thanks to David and Mick for your prompt reply. The local radio doctor here seemed to think it was a cap. or a resistor. I will change the resistor and let you...
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the FM900 group. File : /FM900 Preamp.zip...
FM900@yahoogroups.com
Feb 7, 2003 10:55 pm
3255
any chance off that bin file? regards m ... From: "Grant Ottaway" <Grant_ottaway@...> To: <FM900@yahoogroups.com> Sent: Friday, February 07, 2003 2:59...
Could someone please send to me an eprom with following programming. ALL CFA FREQUENCIES REGION 22 CHANNELS AS SCAN GROUP 1 NO OTHER SCAN GROUPS ** PLUS ADD...
Hi All We Would need to know the type of radio and whats fitted, to generate *.bin file for you Fm900 have various configurations and there is no standard type...
And the radio will need the 25kHz to 12.5kHz mods if it is an old 900, so you may need to know the reference oscillator crystal frequency as well... Mark....
Hi all , I am in need of a later version of the Fpp software than I have - I have version 2.2. My problem is that I am unable to program in DNRE (DSE now!)...
Ver 2.2 should do it. Make sure the hardware code is set for 12.5kHz spacings. Depending on the IF and head type, the fourth digit will be: 5 = 10.7, Local,...
Hi Don, Can't help with the FPP, but didn't you live in Nunawading ? I remember buying an ETI terminal from you. You also gave me a SWTPC DC1 floppy disk...
Hi Mark, Thank you for the info but that side of things are all under control and working ok. The problem is in the fpp program. the version 2.2 uses as a...
Hi fellas, aqquired a A Band FM900 on 2mtrs i need to change some power settings, but the radio doesn't have a ID Plate on the side like most Philips all it...
Hi Dennis Where are you?. If in melbourne contct roger baker VK3BKR .If you are going to use it on 2Mx he will have a prom that will work with the standard...
Hi Don Eproms and getting the progs and channels in are not the problem, as not having a HARDWARE CODE on the rig, just burning an eprom and sticking it in...
yes it can NOT JUST WORK, i have one that works with a loud squeal on TX, no adjusting makes and difference, i have just tried a new prom now , and the rig...
Hi again Dennis, do you have the philips charts for hardware and software codes? If you do you should be able to pick the most basic options and it should work...
Ok Don, again ai appreciate the replies. ok i want to use this as a IRLP rig, i have beenm using it as a IRLP rig, but it has set programed to 25ws out on all ...
Dennis, It is also possible to hard wire a switch into the rig to switch the power settings. I have done this in a couple of mine as I didn't want to waste ...
Thanks Eric, no hurry but if you find it by accident i would be interested Rgds ... Dennis, It is also possible to hard wire a switch into the rig to switch...
Have a look at http://ozradio.wireless.org.au There is some basic fm900 info including location of a resistor to bypass the low power settings and a simple...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
