I used to have something similar. It was a gun-style iron, the trigger advanced the solder towards the point of the iron. I never found it very useful because...
53367
mwh87120
May 1, 2009 2:01 pm
Dave, I do not see any components from your schematic that, if altered, would increase motor RPM...apart from increasing the motor supply voltage which could,...
53368
davec
davec2468
May 1, 2009 3:50 pm
<http://i43.tinypic.com/24busm9.jpg> I have received suggestion that R1695, if reduced, would increase minimum motor speed. Surely increasing fan speed (which,...
53369
Terrance
evil666demonic
May 1, 2009 4:20 pm
Ok, I took a quick picture of this. Forgive my shaky hand and bad picture, but I think it is showing what you must be confused about. ...
53370
Erik Knise
elknise
May 1, 2009 4:32 pm
I know it's wrong, but I normally hold the solder in my mouth and tack the part in. Then I finish it up with two hands. Make sure to breathe out while you...
53371
Stefan Trethan
stefan_trethan
May 1, 2009 7:27 pm
Thanks for both replies. I shall try again some time. I got almost burnt because I had to stick my finger further forward in order to compensate for the solder...
53372
Dan
d_wolstenholme
May 1, 2009 8:49 pm
Seawater is one of the most corrosive liquids commonly available. Some things resist it better than others, but they're not completely immune to it. If you...
53373
terramir
May 1, 2009 10:15 pm
I have this thing called END electronics network designer it uses huge boards (7 5/8in. x 6 7/8in) a breadboard under it and you can close the top which has...
53374
jong kung
jongkung01
May 1, 2009 11:13 pm
$T, ... Few years ago, me and my close friend went to Hong Kong electronics show. This is where people ALL OVER THE WORLD come to get their electronics...
53375
jong kung
jongkung01
May 1, 2009 11:27 pm
Steven Trehan, Lately on Discovery Channel they've been airing a new show Pitchman: http://dsc.discovery.com/tv/pitchmen/pitchmen.html From what I can tell,...
53376
cary heestand
packrat0_15
May 2, 2009 12:09 am
iv'e been a member for a while but this is my first post. i'm a newbie to electronics but have built some kits and can follow a scematic. i have a circuit that...
53377
Erik Knise
elknise
May 2, 2009 12:38 am
I just remembered something else. At my old job I kept my solder spools hanging on a large bolt. I sometimes just spooled out 8 inches or so and moved the...
53378
jongkung01
May 2, 2009 1:08 am
Cary, ... Basically you want to set a reference voltage of 6 volt and 8 volts. Correct? Why even use a POT? Just get some Zener diode and use them as...
53379
Howard Hansen
hrh1818
May 2, 2009 1:16 am
Steven, the following Yahoo group may be of interest to you. http://finance.groups.yahoo.com/group/pcbindia/ They also have a home page at: ...
53380
Brian
blue_eagle74
May 2, 2009 3:39 am
I was reading every post until now. This thread was about renewable energy. Where did this 'identify componet' come into play? shouldnt this be posted...
53381
Erik Knise
elknise
May 2, 2009 3:43 am
If you read these by e-mail. Some people reply and changed the subject to start a new thread instead of actually stating a new thread. Via e-mail it looks...
53382
Stefan Trethan
stefan_trethan
May 2, 2009 4:59 am
Something like this: <http://at.farnell.com/productimages/farnell/standard/42348702.jpg> ST...
53383
Steven Trehan
steventrehan
May 2, 2009 5:19 am
That was my mistake, To start a new thread, I usually press reply button. Then delete all previous contents, write new text, change subject line and send. That...
53384
Stefan Trethan
stefan_trethan
May 2, 2009 6:13 am
You mustn't start a new thread that way. Some thread ID gets retained in the header and it is attached to whatever thread you took. Instead, make a new email. ...
53385
terramir
May 2, 2009 7:40 am
when I put two of these chargers http://www.shdesigns.org/lionchg.html (version 2 pdf) in parallel on the psu and connect one to the one of the batteries to...
53386
Musabbir Majeed
musabbirmajeed
May 2, 2009 11:16 am
Hi all, I have got a system which contains various sensors. The sensors will send the data to the microcontroller. I have assumed that I have a microcontroller...
53387
leon Heller
leon_heller
May 2, 2009 12:29 pm
... From: "Musabbir Majeed" <musabbirmajeed@...> To: "Electronics Group" <electronics_101@yahoogroups.com> Sent: Saturday, May 02, 2009 12:15 PM ...
53388
lathegear
May 2, 2009 12:42 pm
I found a component in a box at sale and would appreciate it if anyone can tell me where I can find a data sheet or other info on it. Tried websearch but no...
53389
Dave Mucha
dave_mucha
May 2, 2009 1:55 pm
hi all, I am looking for a small (bullet/cigar/lipstick) video camera, B&W would work for home inspections. It would need to have lights and be able to fit...
53390
Steve Greenfield
alienrelics
May 2, 2009 2:40 pm
Make Magazine has put up some videos explaining basic electronic components. Diodes, transistors, capacitors, etc. They look pretty good. Here is one on...
53391
Howard Hansen
hrh1818
May 2, 2009 2:49 pm
What type of modem are you thinking about using? Is it a dial up modem, a DSL modem or a cable modem? Howard...
53392
Steve
alienrelics
May 2, 2009 2:52 pm
Sigh... nodoby's perfect. At 6:12 in their video on Transistors, they make an incorrect statement. PNP transistors do -not- act opposite to NPN transistors....
53393
Howard Hansen
hrh1818
May 2, 2009 3:08 pm
The following Web Page show a window comparator with independent trip and window adjustments. Take a look and see if the circuit shown will meet your...
53394
fahad ayub
buitms2003
May 2, 2009 3:10 pm
Hello, I want to convert 12v dc to 18v dc of 3A, please any one give me circuit diagram. Thanks & Regards [Non-text portions of this...
53395
Steve
alienrelics
May 2, 2009 3:10 pm
PLEASE DO -NOT- REPLY AND THEN DELETE, THINKING THIS STARTS A NEW THREAD!!! Sorry, I'm getting quite frustrated about this, it is in the files you get when you...
