Good morning Jerel, I am interested in your engine package for $2500. Could you tell me what the HP for this engine is? Also, where is the engine located? I...
Soory I haven't been active. Ive been working on a show that opens tomorrow and Ill be back at the DF soon. I took the corvair out and had my crank nitrated. I...
Please do keep us informed. I'm going to have to remove my crank and have it nitrated too, and I'm about ready to order a Sensenich prop myself. We sure...
Good afternoon Jerel, I am interested! Could you send me pictures? Also, where is the engine located? Thanks, Mike df_jerel <df_jerel@...> wrote: Due to...
I am gathering parts for my electrical system. One of the things I am doing is isolating the two vital buses from the alternator via rectifiers. Each vital...
That's a standard voltage drop. But you're probably making the same mistake a lot of guys make, trying to isolate things needlessly. Take a look at the...
Howdy Group, I wanted to get some advice on extending the seatback a few inches aft...I am 6'1". Do you think I need to move it back to make it more ...
Hi Josh, Is your height more in your legs or in your torso? I'm 6'5", but I have a 33 inch inseam, so most of my height is in my torso, with the result that ...
Hi Josh, Yes, you can (and probably should) move the seat back at least 3". I did and am 5' 11" and I fit pretty well. Many other vertical over acheivers...
I am 6'2" 35" inseam with the seat back as designed. Getting in and settled is a matter of sliding forward and down into the seat. While cruising I can pull...
I am 6'3" and 34" legs, 39" sitting height. I can fit in mine, but I had trouble fitting in Chuck Ufkes Dfly. So, apparently there are some differences. I...
... wrote: Howdy Group, I wanted to get some advice on extending the seatback a few inches aft...I am 6'1". Do you think I need to move it back to make it...
Josh, I built a Q200 that I've flown all over this country. I added a removable, quick release 6.5 gallon fuel tank just behind the passenger seat, bringing my...
HELLO Tom!!! Thanks for the good info!!! Question: does "4hrs total" mean 2hrs for the top and 2 for the bottom skins after the shear webs are done? Gene ...
Sorry, that's 4hrs per side. That includes micro, crbon spar cap and peel ply. We all remember that the layup has to be done all at one time (monolythic)to...
Hi guys. Today I breadboarded the ignition for my EA81. I am using the GM 4 pin modules. It takes just a mild turn of the distributor shaft to generate a...
Hello tom!!! Thanks for the extra light on your construction tecnique. Very informative. One last Question. I looked at your extensive photo section. I am not...
Hi Fred, Thanks! Maybe a bit of a stretch to have Dragonfly airplanes picking up where F-15s leave off, but after you've witnessed something like this ...
No worries, The two circles are access holes so that you can install the tank. They are closed up after you finger wipe the corners with really wet flox...
Fred, Sounds like you are making progress ! How close to being finished are you ? Sure would be nice to see round KDEC....Tad ... I am doing is isolating the...
... There will be one, it's just a matter of where. There's no change with the infrastructure at Bullhead (read that as no hangar or indoor space available) so...
Hi Tad!! How have you been? It will still be a few years before I am complete. I work on various things to keep from getting burnt out. I hope to be doing...
Hi, I am interested in your DF but at the moment I am in Canada and will be here for the rest of the month. I will be going to Africa early in March and will...
OOPS!!! Sorry guys!! did not intend to reply to list Martin SPONSORED LINKS Aviation Msr dragonfly Dragonfly shirt Dragonfly decor Dragonfly pendant...
Howdy Again, Thanks for the input on the seatback. Going through the yahoo pictures again and saw that One Sky Dog had put up some FEA screen captures of the...
Check out Message#17000. jon ... will be here for the rest of the month. I will be going to Africa early in March and will stop by by the London office on the...
