Gday All, A mate gave me some home brew beer which amounted to 20lts. which didn't turn out too flash so I ran it through my still today & only got back 600ml...
G'day Jim,you do not give any indication as to how hard you are driving the column.What is the wattage of your heating element?.How tall is your column?.What...
OK....then you agree that 'pressure cooking' used carbon is better than merely boiling in an open container,allowing steam to escape through the whole...
I don't think the pressure will cause any problems. It's not much pressure. Johan Hi, do you think this design below could work? Can the copper pipe go down in...
Gday All, Having just started with my new rig I was wanting to know what is be best to clean up the still & in particular the column where the pot scrubbers...
I always do a run with wate @ full power,just to 'steam clean' the column and packing...I fully dismantle and remove packing from column(after water run) every...
Every so often I pull the stainless steel scrubbers out and bung them in the dishwasher and give them a run through. Yours in Spirit Robert ... From: Ken Grady...
... Howdy, I studied this question wnen I was a youth questioning the teachings of the church I was raised in. They taught that consuming alcohol was a sin. My...
Hi,` Thank God you were interested in what was true! It's definitely better to be confused than to believe a lie! Well, I asked this question on the forum to...
... Dirk The Chinese lay claim to all things that suit them. Nothing against that society as they 'seem' to have ancient records of a lot of things. You know -...
I found a couple of 40 L milk cans this weekend for cheap NZ$$$. They are "Solar Solderless" brand. I think they are galvanized, but haven't tested that with...
zinc a Big no no Cheers Ken Mc ... From: Distillers@yahoogroups.com Date: Saturday, August 02, 2003 7:06:04 PM To: Distillers@yahoogroups.com Subject:...
Blessed those who believe if you know what that mean. stillyaakman <stillyaakman@...> wrote:--- In Distillers@yahoogroups.com, "homedistiller" ... Howdy,...
this should be fine. toddk63 <toddk63@...> wrote:I found a couple of 40 L milk cans this weekend for cheap NZ$$$. They are "Solar Solderless" brand. I...
zink will not be able to rise up the column. you will get more zink by standing on a street with car traffic compared to that of theoretical possibility of...
The Babylonians were brewing beer and it was more widely consumed than wine - so beer and wine would have been known to people in the Old Testament. But the...
In a message dated 7/31/03 11:02:58 AM Pacific Daylight Time, maxime_belair@... writes: << What about the pressure, this still like all other pot stills...
It is not a question of zinc rising up the column. The issue with galvanized pots (just like with aluminum) is that zinc reacts strongly with the acids in the...
From www.Homedistiller.org: Galvanised materials are not safe to use on the condenser side, but if it's part of the boiler or at the bottom end of the column,...
I did the HCl test side by side with a galvnized nail. The nail bubbled, the milk can did not. They must be tinned! Todd K. ... They ... haven't ... the ... ...
galvanized stills were used ta make shine years ago and were called silver clouds. they were generally very big, rangin from 500 gallon ta over 1500 gallon....
The Portuguese planted cashews from Brazil in Indian Goa. The trees apart from provide valuable nuts, but the cashew 'apple' which comes with the nut, is also...
Gday All, A mate gave me some home brew beer which amounted to 20lts. which didn't turn out too flash so I ran it through my still & only got back 600ml @ 93%...
different time zones. printed documents achiving. and what to chat about? all of the above render the thing dead. Ken Grady <kengrady@...> wrote: Gday...
Mike, In "The Compleat Distiller" chapter 8 there's a section titled "Supercooling and Column Stability". If I understand it correctly, you seem to be saying...
Thanks for the previous dicsussion on "Galvanized Boilers". Consensus seems to be..."You can get away with it, but try to find a more suitable material"...
timmur64 wrote: Subject: [Distillers] Question for Mike Nixon Mike, Hi Tim I have taken the liberty of putting in the metric values for your measurements...
