Bob and others, I have heard and used the term RJ-45 for the CAT 3/4/5/6 connectors, I believe it is an eight wire plug. As for the six wire connectors that ...
[To all additional addressees as info and response required only if interested] Dear Digitrax Group, I am a new list member doing prototype modeling of the...
Hi all (and a Happy New Year) ... As announced a few weeks ago, the latest version of WinLok CT LocoNet Extender has full support of the new DS64 device,...
I guess I don't see how you would propose to "reverse one of the functions" of the blue wire. To operate a polarity sensing device (such as a slow-motion...
Since you mention that the install is an AT, I strongly suspect that your install some place does not make good contact from the wheels up to the decoder...
List, Okay so let me see if I understand this issue now. If I MAKE SURE I only have one engine on the programming track and it is COMPLETELY over the BREAKS in...
Sorry, I have not been following this thread. What I would do is have three isolated sections: the main layout, a no-man's land, and the programming section....
Mike: This is how I have done my Programming tracks. I use a DPDT center off 10amp switch that I bought at Radio Shack. I run the wires from the Zephyr ...
I thought you might be able to use diodes to make sure the current only goes where you want it. As I said, I did not know if it would work. It was just an...
... Our DPDT switch is in a recess to: 1. protect the switch during setup and break down. 2. to make the switch throw deliberate and not accidental One of our...
Hi John, I actually didn't think that the supplied connectors were that great so I soldered everything, clean all the wheels, etc. My layout is not ready yet...
I installed a DH123 in a Bachmann Thomas the Tank loco that belongs to my son. On the track it will not start moving until the speed indicator reaches about...
The DH123 does not have BEMF which helps any motor to start at a lower voltage setting. I installed a DH123 in the Thomas engine I have and had a similar ...
It sounds like you're getting very little power/voltage to the program track. I wonder if you have a high resistance connection to your program track, or...
I just bought this starter set, I would hate for that to be the problem. I just did a simple hookup no layout, just a prog track and a operation track to test...
Has anyone seen these. I have two. They are installed in two of my Kato Dash 9 locomotives (both were dcc ready, plug n play). The decoders are 8-pin and do...
... OK, let us assume the programing output has something wrong. You still have the ability to program on the main line. You state the loco/decoder responds...
... Open the DCS-100 and remove the CMOS battery for 10 min. Removing the battery will reset the command station. Then reinstall the battery and close up the...
They are older Digitrax decoders, circa 1995-97,. They came in 2 flavors: DH84FX with lighting effects and (I think) 4-digit addressing. DH84 without. Do you...
... The DH84 was the successor of the DH82 and came out 1994 and was manufactured until 1996. It was the first decoder that used the 9pin onboard connector...
Greetings to all list members. This is my first posting and I am looking forward to what I hope are many pleasurable hours of learning. I have finally come...
Christine Higgott
rail.mail@...
Jan 1, 2006 10:26 pm
94571
... with a hard wired throttled before you start using an RC throttle! Bill \ ... looking forward to what I hope are many pleasurable hours of learning. I...
I also have a programing problem. I'm getting a "d nd" message. Its my first attempt at programing. I've been running the loco for 3 weeks without any...
I have a DH 163 KO ( 163RO is printed in the PC board) that went nuts today. when I hit F4 the engine takes off, full speed, but not all of the time. I have...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
