... Seconded. Definitely worth visiting and with the station right across the street parking is not an issue and you just might have to force yourself to make...
Hi John: From Chapel Hill take either Hwy 54 or Interstate 40 East; Interstate 40 is best. Take the Wade Avenue exit and continue on Wade Avenue to the Blue ...
Did you hit the Save button after changing the option? I had a similar problem until I discovered Save. 73 de KT0T Bob Schwartz Modeling Waseca, MN in the '50s...
Wouldn't you know it? The day of a layout tour, my radio throttles begin to act up. I have a DCS100, UR91, 2 UT4R, 1 DT300R in a 12'x25' layout room. ...
Digitrax List Monthly Reminder! Links to the Digitrax List Archives: Messages at; http://groups.yahoo.com/group/digitrax/messages/ Files at; ...
Digitrax@yahoogroups....
Jun 1, 2005 3:17 pm
86571
Digitrax List Monthly Reminder! Instructions for Unsubscribing from the Digitrax List: UPDATED: 06/03/2000 for eGroups 01/28/2001 for YaHoo! 04/28/2002 for...
Digitrax@yahoogroups....
Jun 1, 2005 3:17 pm
86572
I can't imagine ALL your radio throttles going over to the Red Side at the same time (Darth Throttle?) It could be radio interference. Do you have a cordless...
Mark, You may have a power problem. Have you checked to make sure that the aux power source is plugged into both UR91 and the wall outlet? You may have a...
I'm going out today to buy new batteries just in case, but the original question still stands: Is there a way to FORCE radio transmission and suppress...
Hugh, We use exclusively Peco and yes in this particular case you would be wise to insulate the frogs friom the track! We have done that on our new layout. ...
Al, I discounted both of these because the handhelds all work if they are close to the UR91, and the green activity LED on the UR91 blinks when it does get...
The DT300R can be configured for radio only by changing Option Switch #2 to x43. The default value of x03 enables both radio and IR. I don't believe the UT4R...
For DT300R & DT400R, yes there is, check out the throttle's Option Switch #2: See pages 45-48 of: http://www.digitrax.com/ftp/dt300.pdf for DT300R, or pages...
You said that they worked near the UP panel. were the DT's pointing at the panel or away. If pointing towards you might be using the infrared. ... From: "Mark...
Lawrence, Adjust one truck (tighten the scew) to allow for side to side turnin without any tilt of the car body, and adjust the other to allow fo just a bit of...
Paul, Go to the Digitrax Group and click on Edit Membership. After you select the delivery ( daily digest, individual emails, no email. etc) make sure you...
A nice picture of the UR91 is at http://www.digitrax.com/menu_wireless.php There are two LEDs: "RADIO" and "NET/IR" I'm assuming that the hole beneath the...
I would say that the UR-91 is a bit wheezy. One obvious thing to check would be power. If the local power supply is bad, then power would be taken from the...
did the Antena get moved or bent that could cause a change in preformance. Just a thought. Jeff G. For a large selection of HO Scale Trains visit my eBay store...
Have you checked to be sure the UR91 antenna wires are properly oriented? could they have been folded together after initial install and testing? Harlan...
Thanks to everyone for the comments and suggestions! I did check the V of the antenna, and it was OK. I even bent the wires to try the V at 90 degrees, but no...
They are snap in trucks. Ken ... From: <Cact25@...> To: <Digitrax@yahoogroups.com> Sent: Wednesday, June 01, 2005 2:59 PM Subject: Re: [Digitrax] Re: Heavy...
Mark: I've had a similar intermittent experience. Digitrax said to send it back. I tried it once more two months ago before I shipped it and it was and it is ...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
