Andy, Glad to read you`re satisfied of the results. About the 4F Atlas decoders. IIRC, these come defaulted to low frequency motor control, just the CV9=255...
Larry, The fact that some of your engines run fine, while others are having problems, is a clear indication that it is neither a track problem (as you already...
...Forgot to mention a CV2 issue found in Atlas decoders. When CV2 is set to a value of 8, for example, the next progress in speed after speed step one will...
Looks super!! I bought some SM LEDs from Jim to do gyralights in the nose of my DRG TMs, and the brow of my SPs. The snoot should be no problem as you ...
Consider using a clear plastic overlay. Just about anything you adhere to the panel (label tape, stripping tape, dymo, decals, etc.) will either lift or wear...
... the ... OK, viewing angle is obvious - anything over about 80° is OK, anything less gets awkward. Peak wavelength is a fancy way of specifying the colour;...
... Rex-- I think the plastic overlay Jim has in mind is 1/16" plexiglas or acrylic sheet-- not attached to the panel with the graphics. --Paul E Musselman ...
I am getting ready to install decoders in my Athearn SD45T-2's and need to know how to remove the shells for the installation. [Non-text portions of this...
Thanks Doug I'm not sure if SM LEDs use the same resistance values for equal brightness, so you might still have to experiment. My main lights are 3mm golden...
Would someone guide me in the proceedure of setting up a consist using DecoderPro and a Digitrax DB150? Is it just a matter of putting the same number in the...
I have a small control panel for my Ntrak module that uses a thin plexiglass overlay. Tha artwork was done on the computer and pasted to a piece of masonite,...
Rex: I take a similar approach (plexiglass over computer generated graphics -- glued to illustrator's board) to my control panels... You can see some samples...
Be sure that your not bridging any of the gaps, that would help supply current to the block you what the detect in. Bill Hodkinson [Non-text portions of this...
Trevor, I too would be very interested in seeing the schematic for this. If you decide to send it to those interested, I would appreciate it if you would copy...
Digitrax List Monthly Reminder! Links to the Digitrax List Archives: Messages at; http://groups.yahoo.com/group/digitrax/messages/ Files at; ...
Digitrax@yahoogroups....
May 1, 2005 11:29 pm
85578
Digitrax List Monthly Reminder! Instructions for Unsubscribing from the Digitrax List: UPDATED: 06/03/2000 for eGroups 01/28/2001 for YaHoo! 04/28/2002 for...
Digitrax@yahoogroups....
May 1, 2005 11:29 pm
85579
All I can say is WOW! All that in N scale. It looks really!!! Great!! Thanks for sharing. Now I have a reason to start adding more lights to me fleet. Jim ...
Good Evening All, I have DCS100 that acts differently from the others. When one turns off the track power from any of the handheld throttles or but the...
... Bruce, I had the same problem about 3 years ago with a DB150. I'm running a DCS100 and a DB150. After talking to John (now retired) the DB got to go home...
One of my new UT4Rs has developed a frustrating quirk--it will sometimes be unable to reversed direction. Changing the direction toggle to "off" usually will...
Good Monday Morning. Another simple method, if you like colour, etc. is to print a page on photo paper and have it mounted like a picture on a plague. Then the...
you might try some transparency material. It is less than 1/16" but not flimsy like Saran Wrap. Would hold up well to use. Cheap at you local Office supply...
Just a suggestion. If you want something thin, why not laminate your artwork (no matter how you make it) inside sheets of plastic. There is a way to...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
