... Search the web, there is quite a bit of info out there on doing this. Quite easy to do. All you need is a home oven and vacuum cleaner, along with some ...
I bought UNIVERSAL CELL PHONE holder at the $ Store. Sized them to the throttle, drilled holes and screwed them to the layout facia. Cost $1 plus screws. They...
Definitly used the likes of a DH163 so you can use the Back EMF feature. Athearn loco runs very wheel with it. Nigel Western Pacific Model Railways ...
I would be interested in about twenty of them......think you may find a good demand for them! R/Phil Euper in South Carolina ... From: "Frank A. Rosenbaum"...
Presuming that you're talking HO, you should have no real problems with this installation, since the motor is isolated from the frame. Most decoders designed...
Of course, my suggestion was under the assumption that one has done a stall test with the old loco! My Trix locos all have the same motor, and it draws about...
I just bought several DN163A0 decoders. The dealer had wait to restock, so these are the latest from Digitrax. The first thing I noticed between these and...
Yes, I meant to say take off. What happens is this, oh and by the way, I have a big boy system. I have a train in a staging yard. It has a soundtrax decoder, ...
To: bernard messenger Confirm that the Soundtraxx decoder 'Analogue Mode' is disabled. Do this by subtracting '4' from the value that is in with CV29. My...
I would agree that converting one's analogue locomotives to DCC has all sorts of incentives and advantages which will become only too obvious to just about...
Hi Bob, I think you found the cause of this irratic behavior. After checking the decoder with the PR-1, I found that I had a value of 2 in CV29. After checking...
To: Bernie CV29 at 12h = 18d = 10010b or in words '28 Speed Step' with 'Speed Table Enable'. If you mentioned the specific Soundtraxx decoder I missed that...
I cant program any of my engines. I try to program with the instructions, but when I put it on the track it does not take. It works when I dial in #3, but it...
81767
digitrax@yahoogroups....
Feb 1, 2005 8:40 pm
Digitrax List Monthly Reminder! Instructions for Unsubscribing from the Digitrax List: UPDATED: 06/03/2000 for eGroups 01/28/2001 for YaHoo! 04/28/2002 for...
81768
digitrax@yahoogroups....
Feb 1, 2005 8:40 pm
Digitrax List Monthly Reminder! Links to the Digitrax List Archives: Messages at; http://groups.yahoo.com/group/digitrax/messages/ Files at; ...
Mark, I know you are frustrated, but a little more information would be of some use. How are you trying to program? Since you have a DB150, there is no...
Claude my db150 have program a and b output the thing is the db150 dont have read cv You have to put the loco on a program track plug to the prog a and prog b...
-Mark Tell us a little more about your set up. Do you have a track dedicated to programming and is it hooked up to your db150 programming terminals and...
To: Mark The DB150 does not have a 'programming track' as such. Connect your DT400R to the Loconet port on the DB150. Ensure that the only locomotive on...
Mark, I just installed two Digitrax DN163 decoders last week with the same setup. Here is the procedure I used: 1) Place the loco to be programmed (and no...
Sorry Claude i make a mistake I was looking at my dcs100 ( i switch place yesterday , the db150 have a config a and b no program a and B Just make sure you...
Hello I just try the demo version of DCPro of Kam on 3 different Pentium 4 computer and the software always crash and overload the cpu like i never be abble to...
Thanks for answering my querry. I picked up one. Thanks again. George Bstricklan@... wrote: George, I have a PR-1 that I do not use any more, contact me at...
If anyone can hook me up with others using RR&Co to run a Digitrax layout, I have a ton of questions and can't seem to get any help on the RR&Co forum web...
Paul: You got a winner with your throttle holders. You should be able to make enough dollars to pay for all your DCC equipment. Go for it! If you do decide to...
Hman56(???), I hang out a lot over at the RR&Co Forum, and haven't noticed any posts from you. My AT&GRR is all-Digitrax and makes extensive use of ...
