... Yeah, that was them thanks. Did not appreciate they were in the photos section, thought they were on someone elses web page. Got some guys at my local club...
Hi Guys, I've got one of the new Kato N-Scale CZ's on it's way to NZ, but it's not going to arrive until after Christmas :(( due to it being brought to NZ via ...
Alex, I too have a CZ set and CB&Q A-B-A on its way, should be here Friday or Monday. From the Atlas N-Scale forum.....The CZ set is approx 6.5 feet with a F3...
Hi Group I am open for suggestions - - Wondering how I can configure / control 3 rail track for two different DCC voltage levels - Nn3 (9 v) and N (12v). The...
... I've ... the ... painted ... how ... has ... I ... in ... year, ... to ... out ... Tim, Walthers now has DCC friendly #6 double crossovers in code 83....
David, yes that was the one. Thanks. As it turns out, I had used that diagram to make Gartner's double crossover changes. Where I'm having problems is with the...
... I was not aware that DecoderPro works with a PR1. I have installed DecoderPro on my notebook (running XP) and was using this to store all my CVs and using...
If it was left alone and both sets of points are thrown at the same time there would be no problems. Chris Marco [Non-text portions of this message have been...
A big Thank you to: Rich Black Dennis Rockwell Jeff G And Gerard--- Your second language English is fine--you wouldn't want to see or hear my second language...
Hi Cgregory7, You wrote: "I have had some success as a temp measure putting masking tape (cut a sliver) along the outside of the point rail preventing the...
Gang, I sure hope that these CZ sets are not in A-B-A configuration..... the CZ did not run that way. A-B-B was the right way Enjoy grant ... From: "Phill"...
Digitrax List Monthly Reminder! Links to the Digitrax List Archives: Messages at; http://groups.yahoo.com/group/digitrax/messages/ Files at; ...
digitrax@yahoogroups....
Dec 1, 2004 4:46 pm
78751
Digitrax List Monthly Reminder! Instructions for Unsubscribing from the Digitrax List: UPDATED: 06/03/2000 for eGroups 01/28/2001 for YaHoo! 04/28/2002 for...
digitrax@yahoogroups....
Dec 1, 2004 4:46 pm
78752
CB&Q ran ABA, DRG was ABA or ABBA, WP was ABB. Good luck in finding a separate B unit. Doug ... the CZ ... Zephyr ... Friday or ... 6.5 feet ... Zephyr ... me?...
Hello: I'm having a bit of a problem programing with my DT400 and DCS100. I've been successful in programing for the most part but lately it's getting harder...
To the wisdom and experience of the group, This is the first year I have been using DCC. Question: As winter approaches with colder and dryer air, is static...
To: David Long It is always best to have all functions (lights) turned 'Off' when programming any decoder. This is especially true for NCE decoders. Bob...
... Actually, no, DecoderPro does NOT work with the PR1. DecoderPro requires a command station to operate - it simply instructs the command station to carry...
Michael, I live in Somerset, PA and know just what you mean. I haven't experienced any problems with static and the temperatures range from 65 to 100 degrees ...
... Ok, can that idea!! :'( ... The lights are wired to the decoder. I have the white going through a 2.2kohm resistor to a LED, the return to the blue. The...
Team, Has anyone encounter having a problem removing a loco from the consist? I have a loco that will not come out of the CONSIST. I have used the DT400 and...
rockriverrr@...
Dec 1, 2004 9:17 pm
78763
Try Tough as Nails; find it in the cosmetics counter. Glen Duke ... From: André Kritzinger [mailto:grela@...] Sent: Wednesday, December 01, 2004 10:58...
Most "new version" decoders program best on "direct mode". I have a few NCE D13SRJs and have no trouble at all with DecoderPro. DecoderPro defaults to...
I ended up changing out decoders. Two of them; finally got one to program. Thanks for the advise! David L. -- No virus found in this outgoing message. ...
just got back from the home depot with 4/500' coils of 12 awg at a tune of 30.00 smacks each , going to hit the train room soon with my trustee drill to bore...
... Alan Some additional information: The short was caused by an operator running the locomotive against a switch, and letting it sit there for quite a while....
We've found that running the wires through holes in the joists make the wire difficult to install and change. Instead, we clamp the wires to the joists using a...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
