Actually, it does not have to talk to Loconet to perform auto reversing. If the TTX also offered detection or other functions, then the Loconet connection...
Brad, I have been following this thread for a couple of days now and I would like to point a few things from my point of view. 1) The PM42 is a multipurpose...
The short answer is No. The side connector on the UP 5 is only a Throttle connection. The loconet can only work through the two rear connectors. Bob Wintle ...
Actually the DB150 is behaving normally; it cannot do service mode programming and run the layout together at the same time. So put it into program mode, and...
... out of ... different plug in ... splitter. If not ... Ken, you can use a series of "Y" splitters plugged into either the two rear jacks to achieve multible...
I should have said that the DB150 does not have separate programming TRACK outputs. You set the throttle to programming made and program on the main. Ken ... ...
Al Silverstein wrote, If you use the PM42 messaging then it ... message on ... immediately ... district. ... conjunction ... SE8c signal ... lost its ... ...
Hi group, well, my PM4 problems are solved. Since I have Decoder Pro, I decided to connect the PM4 to the Loconet to see what was happening. Since Decoder Pro...
You can often find 6-wire flat cable with connectors at your local Best Buy/Circuit City/Radio Shack as well as on-line. It is typically referred to a...
Ken, As stated above, the UP5 side connector (as well as the two front connectors) are for throttles only. For general Loconet branching, you can use a series...
I use a PM42 as a reversing unit and to split up the output of a DCS200 into two power district. I am planning to add a DB200 at a later state, at which I...
A friend of mine went to a club he was a member of until he moved to run some trains. The club has an "N" scale layout and a "HO" scale layout. He was there to...
First, there is only one frequency for Digitrax radio throttles and receivers. (A second frequency was once offered but was withdrawn about 5 years ago.) ...
Manfred, Spoke to Armin at Digitrax this morning, and walked through a few DB150 tests. His conclusion - send it back for service. Guess that ends the...
... that ... Robin, the DB150 is meant to shut down after sending a programming message,"When the DB150 running as a command station receives a programming...
They did not provide an explanation; Digitrax just sent new cards the first time and sent the PM42s the second. We did like the ability to subdivide booster...
Hi, Lately there have been some strange things happening on my layout: Last night after parking a train and unplugging the DT400, about a minute later that...
Sounds suspiciously like you have 'stolen' the address from another throttle - even if it is the same DT-400, but from the other knob.... You could clear the...
I've had some similar anomalies accruing on my layout. I've had several trains in my staging yard runaway with the power to the track off. The last time it...
Ted/Ted: ... This sounds like a broken/misconnected loconet wire... If you haven't already, check the UP-3 (and all other jacks) with a LT-1 and make sure all...
All, I have a Richmond Controls gyralite module and want to incorprate it with my decoder. Would I wire it to the front headlight lead of my decoder?...
Hello all from a newbie to the list, I just bought four of the plastic-shaft encoders from Digi-Key about three weeks ago. They work fine, but are a bit stiff...
I have several European style locos in which the decoder is visible through the cab windows. Is it possible to paint or place tape over the decoders to reduce...
I have a friend who has been using a PR-1 for some time, with Windows 3.1 software. He is interested in finding an alternative for off-railroad loco...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
