Allen, CV62 controls dimming and effect rate. I dont`t remember which hex value controls dimming, the upper or the lower digit. To find out simply give it a...
Good morning everyone. Just a quick one to ask. How do I get the headlights to match the direction without changing the hard wires? I know it can be done but I...
John, the BDL162 replaces the BDL16. The SE8 and SE8C are long awaited devices that, hopefully, will become available in the near future, a couple of months...
Same problem. The track status LED on my Chief (4 1/2 years old) was dead out of the box. I'm a tech and called Digitrax for advice. We determined that the...
I have an Athearn blue box Amtrak AMD103 that I have installed a DH121 in, and after programming, this engine will not run. Here is how I installed the...
If you have the DCS100 command station you can use stopping blocks There is a setting in the command stations to set the programming track outputs (when not...
... Carl, You didn't mention which decoder you were using, but if your decoder supports function remapping, and if it supports the remapping of Fl(f) and ...
Didrik, Pins 3 and 7 are normally missing from the dummy, or dc plug. you should notice that pins 1-2-8 and 4-5-6 are connected together to connect the lamps...
leroystew07 <Leroystew@...> wrote:I have an Athearn blue box Amtrak AMD103 that I have installed a DH121 in, and after programming, this engine will...
You may want to look at the connecting wire to each truck. It is unclear what the wires connect to, but if it is the motor, you have not isolated the motor...
Today Digitrax announced the following upgrades to their product line: 1)All DT100/300/400 encoders will be replaced with high quality components at no costs....
Manfred, Are you saying, in your second paragraph, that the BDL16-2 version is needed for train ID-transponding to work correctly? R/Phil Euper in South...
Phil, no, what I wanted to say is that the BDL162 or the BDL16 with upgrading kit and a RX4 is necessary to get ops mode read back capability. Sorry, if I was...
Mike, I want to get the best possible products and I want to get them from Digitrax because I decided to go Digitrax about six or seven years ago. At that...
Greetings all, I have 2 surplus DT-100 for sale. Asking $75.00 each or best reasonable offer. The throttles work fine, just upgrading to newer models. Please...
With a new Zephyr wired to a basic Kato Unitrack oval, I ran a new analog Kato N SD70MAC. It ran fine for about 30 minutes until I started seeing blinking...
Sorry I took so long, I wanted to be sure of my facts before giving the answer. In short we had problems putting a chip into the Flying Scotsman by Hornby....
Carl, Tell CV50 to be on when going forward, and CV49 to be on when in reverse. Regards, André, Cape Town. Converted from Horribly Oversized to Normal in 1978...
Blinking zeros are a short, actually called walking zeros. See page 32 of your manual. Sounds like the engine had a short and the fact it doesn't run and...
A DecoderPro workshop will be held this Saturday, April 5th., at Papa Ben's Train Place in Houston, Texas. The workshop begins at 10:00 AM and will continue...
Thanks for your reply. I will have another engine in a week or so. I'll wait until then to try to isolate the problem. Ed ... See page 32 ... doesn't ... ...
Hello Lee, Make sure you have set the default loco address on your throttle to '03'. This is the usual default address for new decoders. Also set the speed...
What is the objective of your desire to "drop the DCC track voltage"? Are you trying to power something from the DCC signal on the rails or are you trying to...
... Thanks John, and others who replied privately. The reason for needing to drop the track voltage is to be able to safely power motors of lower voltage than...
Maybe this has been discussed before and there's a quick solution. If so, sorry to waste the bits. This is the second DN121 that has behaved this way. On each...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
