The 10 Commandments of Email Thou shalt include a clear and specific subject line. Thou shalt edit any quoted text down to the minimum thou needest. Thou shalt...
16541
John Burkhardt
burkhj@...
Mar 1, 2000 8:59 am
To all, There have been 8 messages on this thread, not one has addressed the original question posed by Wally?! John Burkhardt ... panel. ... or...
16542
Dennis Cook
dennis.cook@...
Mar 1, 2000 9:22 am
John; Don;& Peter Thanks for your help. That all makes alot more sense and I can understand it so far. I am now going to install it all. Therefore you may well...
16543
Wally Webb
wallyw@...
Mar 1, 2000 10:43 am
Don, Something else I was thinking about, If different people have different size bus wire on their layouts then maybe the short circuit currents could be ...
16544
Frank Rich
frich@...
Mar 1, 2000 11:54 am
a while back I inquired about repowering an N scale atlas Mikado. Doug Tomelinson referred me to Maxon Motors. I have received from them a listing of various...
16545
topcat@...
Mar 1, 2000 12:07 pm
11 th commandment When announcing an event include the state and country in the heading. I've lost track of the number of messgaes I've read about an open...
16546
Wally Webb
wallyw@...
Mar 1, 2000 12:28 pm
I do the same as you for the same reasons. Wally. ... From: Piquette Jean C DR NPRI <piquettejc@...> To: <digitrax@onelist.com> Sent: Tuesday,...
16547
edmajr@...
Mar 1, 2000 12:57 pm
Hi Tia The part number for the screw is 200001, they are 12 for $1.75. The bus bar is 200002, and are 6 for $1.50. Ed Majury...
16548
Harold G. Jones
hgjones@...
Mar 1, 2000 1:05 pm
Bill: Use the 2 digit address and use the aliasing feature of the Chief system. This way the 2 digit address does not have to mean anything and you can...
16549
Harold G. Jones
hgjones@...
Mar 1, 2000 1:11 pm
George: I have a Chief system and have no problems with analog except that they do run a little slower than with a decoder. My locos are brass for steam with ...
16550
Harold G. Jones
hgjones@...
Mar 1, 2000 1:14 pm
Doug: If you the plug you are refering to is the same as I have on my Chief contact Digitrax. They sent me a couple gratis. This is good PR. Harold G. Jones. ...
16551
Wally Webb
wallyw@...
Mar 1, 2000 1:26 pm
Thanks, Don, Brad and Greg for the info on the PM4. Wally Webb Port Elizabeth South Africa GN/SP&S, HO Modeler, Spokane, Circa 1968. GNRHS Member, Digitrax...
16552
edmajr@...
Mar 1, 2000 1:35 pm
Hi Tony's Train Exchange sell a Power Shield which is a circuit breaker device. The Power Shield is installed in series with the power district. If there is a...
16553
Wally Webb
wallyw@...
Mar 1, 2000 1:40 pm
Joe, My problem is that when approaching an incorrectly set turnout from the frog side of an Electrofrog type turnout is that as soon as the engine crosses the...
16554
Bill Roger
billroger@...
Mar 1, 2000 2:45 pm
Hi Guys: I'm trying to match the speed of two Athearn Amtrak AMD's. I've set Vstart and Acceleration to zero. Both have DH121's, programmed to the same ...
16555
Bill Hubbard
hubbard@...
Mar 1, 2000 3:11 pm
Hi Bill, I have found the motors used in Athearn locomotives to be inconsistent. GENERALLY, you will be able to achieve basic speed match by increasing the ...
16556
Bradley White
valleyln@...
Mar 1, 2000 3:16 pm
Bill, Check CV 3 &4 and make sure they are both at 0. These are the CVs for accelerate and decelerate. Brad White Erie, PA Where the trains still run in the...
16557
Robert Adams
rdadams@...
Mar 1, 2000 3:33 pm
Where can one get ingormation on usuing parallel ports with Winlok? The manual has a short discussion of the pia 8255 but I would like to see a more extensive ...
16558
Bob Young
bob.young@...
Mar 1, 2000 3:37 pm
Bill: Are you using WinLok? I ask this as it appears to me that WinLok gives you the option to use the Digitrax (DH etc., etc.) decoder speed response...
16559
Brinton Jones
bmrjones@...
Mar 1, 2000 3:44 pm
KATO HO NW2 Factory frames machined for 9 different decoders. Does not void KATO warranty! Digitrax DN140, Digitrax DH140, Digitrax DZ 121. Dynatrol D102DS, ...
16560
Piquette Jean C DR NPRI
piquettejc@...
Mar 1, 2000 3:45 pm
Hi Don, ... Thanks for your reply. Yes, indeed, I usually operate alone, and I do prefer the booster to just shut down the whole layout (even my drones on...
16561
Jeffrey Witzel
jwitzel@...
Mar 1, 2000 3:57 pm
Thanks Everyone, I got the ouputs working. I now can throw my switches, single and double. I do have a track crossing which throws 4 switches, using 4...
16562
Robert C. Schwartz
rcschwartz@...
Mar 1, 2000 4:52 pm
Wally, have you thought about using fiber optics to indicate if the short detect lights are on?? 73 de KF0WM Bob Schwartz Bloomington, MN ... From: Wally Webb...
16563
Jeff Warner
jwarner@...
Mar 1, 2000 6:04 pm
Bill: When you say "takes off like a shot", do you mean it achieves pretty much full speed on speed step 1 or 2? If so, there was a problem with some of the...
16564
Marshall D Abrams
marshall.d.abrams@...
Mar 1, 2000 7:21 pm
... I guess for this purpose the waveform doesn't make any difference? ... When I bought my chief all that came with it was a two color LED. So I wired it up...
16565
Peter Olivola
polivola@...
Mar 1, 2000 11:00 pm
I need to get decoders in an A-B-A set of custom painted Stewart F3's for a show in about two weeks. What are the options? My dealer recommended the DH150K,...
16566
Don Crano
donc@...
Mar 1, 2000 11:42 pm
Bob, Have a look at: http://www.rr-cirkits.com/ I think you will find Dick Bronson has covered everything you need.<g> Remember Always Have Fun and Enjoy!, Don...
16567
Don Crano
donc@...
Mar 1, 2000 11:45 pm
Wally, I know where you are comming from on this. There has been some problems along these lines with another brand decoder and command station combos. But it...
16568
Don Crano
donc@...
Mar 1, 2000 11:48 pm
Frank Of the two choices you show, there is only one that would work, that is the one with a 12 volt rating. Remember Always Have Fun and Enjoy!, Don Crano...
16569
Jedalberg@...
Mar 1, 2000 11:53 pm
Don, all my UP-3's are wired to the track. As I noted the BT throttle is now working ok--the Jersey City yard operator had no problems. Also was using new ...
