... and ... hit ... shows ... decoders.Try that but remember TAKE ALL LOCOS OFF THE MAIN or they'll get reprogramed as well. Well I don't know why but last...
Rod, As Martin mentioned, check your power supply. Also, with your DT400R unplugged, remove the battery. Now put the battery back in and watch the screen....
Steve, Sounds like you were net getting CV29 set to make the 4-digit address active. Try reading the 4-digit address and see what it is. If it is 4150, change...
Hey List, LAST CHANCE... I can still fit you in if your interested in giving a clinic at DCE. I still have 6 time slots left. Just contact me off list or...
To re-program a Bachmann loco you have to be on the main and use ops mode. If you have any questions look on the BLI web site they tell you how to do it. Jack...
I am not sure if you are asking about using the contacts or installing it to operate the switch. I will try to answer both. To install them on a turnout I...
I have a loconet repeater (LNRP) and a UP5 connected together by a wire between the solder pads so that one PS12 can power both. I've been reading all the...
hello i own the DN143IP for ho scale, my question is is can i hook up ditchlights to the board and make them flash when i blow the locomotives horn? and if so...
Hi Bob: After reading your email several times I believe that everything is operating as it should, and your color coding is correct. First the LNRP manual...
Hi Folks: This email is intended for those readers who will be attending the 2008 National N Scale Convention "Derby City Express" in Louisville KY from June ...
Very suddenly, an Overland TCS A1X equipped HH660 would not respond to its address 1603. On the program track, its address now read 16383 (Decoder Pro), and...
Hi Martin, I am using a Digitrax PS2012 to power the DCS200 and the output from the PS 2012 to the DCS200 is 18.18 VDC using the "HO"scale output setting,...
Thanks for the tip on the batterys Mike, that improves it even more. Loaded ouptput on the PS12 is 14.56 VDC and unloaded output is 16.91 VDC so...
Hi Martin, I am using a Digitrax PS2012 to power the DCS200 and the output from the PS 2012 to the DCS200 is 18.18 VDC using the "HO"scale output setting, the...
... It sounds like there's something electrical on the programming track that's confusing the command station. It thinks there's a locomotive there (so the...
... I've been unable to access their site for about the last hour. -- Drew "Nothing in life is to be feared. It is only to be understood." --Marie Curie...
Digitrax List Monthly Reminder! The 10 Commandments of Email Thou shalt include a clear and specific subject line. Thou shalt edit any quoted text down to the...
Digitrax@yahoogroups....
Jun 2, 2008 6:47 am
129554
Bob, Thank you for this info. I currently run JMRI and LocoBuffer II (serial port). Would you advise I buy a PR2, or PR3 to use with Digitrax sound decoders. ...
I haven't been able to get on all day. GA. ... From: Dave Manary <dave.manary@...> Date: Sunday, June 1, 2008 10:15 pm Subject: [Digitrax] Digitrax Web...
You must live a good life. I've been unable to acces it all day. They must be in the middle of one big update with all sorts of new stuff or the server crashed...
... change ... You're probably right but I think you mean CV29=34. 32 will give you 4 digit address but speed step control of 14. 34 will give you 4 digit...
I had a similar problem with the original DH165A0's, back when they first came out. Every time there was a short on the system, or crossed a reversing loop...
Thanks John Digitrax web site was down all day, and stupid me misplaced both of my LNRP manuals, so thanks for the power light info. ... throttle on ... ...
I do not understand why people are talking about Bachmann decoders under this heading! The FDT (Factory Direct Trains) Trackmobile has an NCE decoder in it....
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
