Please send me a list of any Roland engravers you may have for sale. I am in ohio and need a Roland for a highschool project. Thank you. Roger Gipson...
293
nekpopj
Jun 28, 2010 1:43 am
... Roger, I have a PNC 3000 in A1 shape, but I don't know what it is worth. John Popken...
294
roger
tecfacet
Jun 28, 2010 11:03 am
Can you call me tomorrow to discuss this? Email me: tecfacet (at) yahoo.com Roger...
295
dave_mucha
Jun 28, 2010 11:06 am
what is check mode ? make sure all the cables are conneced. hit the home key and see if that helps....
296
nekpopj
Jun 28, 2010 2:52 pm
Can anyone help me with the value of a PNC 3000 in real good shape? I'm tring to help out Roger with mine but I don't know how to price it. John...
297
db
farmer_dave_db
Jun 28, 2010 4:18 pm
set of collets with machine? My guess is $2500 - $3000 USD for machine with collets set. Farmer Dave From: nekpopj Sent: Monday, June 28, 2010 7:52 AM To:...
298
tecfacet
Jun 28, 2010 4:24 pm
Ha Ha Ha .... ... From: db <dbueckers000@...> Subject: Re: [CAMM-3] PNC 3000 To: CAMM-3@yahoogroups.com Date: Monday, June 28, 2010, 12:07 PM Â set...
299
cyberzl1
Jun 28, 2010 4:43 pm
Wow! What to buy mine? JW ... From: db <dbueckers000@...> Subject: Re: [CAMM-3] PNC 3000 To: CAMM-3@yahoogroups.com Date: Monday, June 28, 2010,...
300
tecfacet
Jun 28, 2010 4:48 pm
I agree... for that price.. there would be SO SO many machines for sale :-D ... From: cyberzl1 <cyberzl1@...> Subject: Re: [CAMM-3] PNC 3000 To:...
301
db
farmer_dave_db
Jun 28, 2010 5:18 pm
so that s to much then, what's a lowest price? Without collets, machine is worthless. I'm looking for another replacement 1/8 collet. Probly going to have...
302
nekpopj
Jun 28, 2010 7:50 pm
... I do have collets, but that's sounds like a lot of money. John,...
303
db
farmer_dave_db
Jun 28, 2010 8:29 pm
none on Ebay, where else are you going to find one? Machine will pay for itself. Seems like over kill for a high school project From: nekpopj Sent: Monday,...
304
dave_mucha
Jun 29, 2010 2:22 am
If you cannot find collets, make them. I made one for my machine. it was not hardended and ground like I would prefer. For some $$$ you can have the spindle...
305
dave_mucha
Jun 29, 2010 11:02 am
I think for about $200, you can have someone remove the spindle, add the ER collet holder, and put it back together. for another $50 you can get a decent set...
306
dave_mucha
Jun 29, 2010 11:06 am
Here is a thought..... how many of you would want to just buy a whole new spindle, complete with ER collet end ? I think ER-16 goes up to 3/8". I would work up...
307
tecfacet
Jun 29, 2010 11:10 am
I would be interested possibly. Â ... From: dave_mucha <dave_mucha@...> Subject: [CAMM-3] Re: PNC 3000 - ER Collets To: CAMM-3@yahoogroups.com Date:...
308
david876474
Jun 29, 2010 11:14 am
I'd be very much up for an ER spindle. I would want to source metric collets for it though ;-) Regards, Dan...
309
Randy
drlogan2002
Jun 29, 2010 2:15 pm
Hi Dave, I'd be interested but it would depend on cost - any rough idea on what prices might be like? Thanks, Randall...
310
dave_mucha
Jun 30, 2010 10:48 am
I will work up some blueprints this week. And send it to my local shop for prices. If we can get 6-10 I think the cost would be decent. the work is not that...
311
Steel Wings
norust2001
Jun 30, 2010 3:43 pm
I just replaced a set of spindle bearings. The numbers were: NSK # 6003Z & NSK #6002Z (Upper and Lower) I would also be interested in the new collet setup as...
312
david876474
Jun 30, 2010 4:46 pm
While we are on the topic of "general driving" for these PNC-3000's: does anyone have a good supplier of drive belts? I REALLY need a new one. After the stock...
313
tecfacet
Jun 30, 2010 5:25 pm
I would really like to locate the service manual for the pnc-3000.  What ever happened to the guy who had some motor driver chips for sale?  Roger  ... ...
314
david876474
Jun 30, 2010 5:31 pm
We have now have a full copy of the service manual in our files section. Thanks to the uploader. http://groups.yahoo.com/group/CAMM-3/files/Service%20Manual/ ...
315
dave_mucha
Jul 1, 2010 11:01 am
check the files section. there is a decent set of references there. Dave...
316
dave_mucha
Jul 2, 2010 11:03 am
As I understand, for the bearings, P5 is desired. that seems to be some sort of grading or accuracy. It looks like the ER-16 set has a nut with a dia of 2mm...
317
tecfacet
Jul 2, 2010 12:22 pm
I would be happy with er-16. ... From: dave_mucha <dave_mucha@...> Subject: [CAMM-3] Re: PNC 3000 - ER Collets To: CAMM-3@yahoogroups.com Date: Friday,...
318
db
farmer_dave_db
Jul 2, 2010 4:31 pm
every bit I use has is 1/8 dia. Farmer Dave From: dave_mucha Sent: Friday, July 02, 2010 4:01 AM To: CAMM-3@yahoogroups.com Subject: [CAMM-3] Re: PNC 3000 - ER...
319
dave_mucha
Jul 3, 2010 3:43 am
Here is something I have been thinking about. if we were to use the exact same lenght, so that it would hold say, a 1/8" bit at exactly teh same hieght, we did...
320
dave_mucha
Jul 3, 2010 4:23 pm
I just uploaded a simple sketch of the ER-11 and ER-16 ends on the spindle. Files section, and under collets the ER-11 is much smaller the ER-16 nut is larger...
321
david876474
Jul 4, 2010 12:13 am
My vote is for ER-16. There are several times when I'd wish I could use a tool >6mm... Any ETA on getting some made? Cheers, Dan...
