Hi All, I finally scanned all of the missing chapters of the PNC-3000 User Manual. The complete user manual is now available as a single .PDF file in the...
Hi All, I am thinking about getting some colletts custom made for my camm 3, I had a set made a few years ago but I wasn't involved directly with their...
Hi All - I have a pnc - 2500 complete with manuals, upgraded material holder & software. I purchased 2 spare motors from Roland 10 years ago and I installed...
Hi I am trying to program my PNC300 using Desk Proto. I create the toolpaths from my STL geometry and use the PNC3000 (no spindle control post processor)....
Hello! I am new here in this forum and i wander if any one knows witch post processor I can use to get the right nc code in to pnc-3000? I will work in Catia...
Hello All, Recently I was asked to run the Roland PNC 2500 machine by entering G-codes and M-codes. However, I don't have any software or drivers. Need some...
Does anyone know where to get a replacement encoder switch or perhaps recommend a good aftermarket replacement source? The one I have is an ALPS "621U" but...
I am looking to purchase Camm-3 mill in working or almost working condition. Although, any condition will be considered! PNC-3000, 3100 or 3200. If you have...
I am looking for a replacement Switch Panel Console and interface cable for for a Camm-3 PNC-3200. A damaged but repairable unit will be OK too. Thanks!...
I am new to using this machine, i found it in the storage room of my school and decided to try and get it working. When i cut a part using the engraving...
The user manual which in the files sub-directory is not completely. The section 3,5,7,8 have lost. Unfortunately, they are the most important sections for...
Hi all, Does anyone have the missing parts of the PNC3000 user manual they could possibly scan in and upload? i.e. Chapters 1,3,5,7,8 Many thanks in advance, ...
Does anyone have, or know of, a Camm-3 for sale? Mine has a bad ball screw and some other more minor issues so I'd like to either replace this machine or find...
Took delivery of a PNC 3000 yesterday. Everything functions as it should. Just some queries. I postprocessed code using DeskProto. To run this do I simply...
Hi all, The question of aftermarket drivers comes up enough that it seems we should have a decent solution. please add your commnets and ideas ... Pros: will...
Having just gone to try the machine - the spindle motor doesn't turn. It did last time I tried it! I note on the schematic that there is a motor rotation...
Hi I have a camm-3 with no controller unit :( (the one with the curly cord) I've searched and searched for years and can't find one. I need a way to use...
Hi I have just purchased a PNC 3000. I am unfamiliar with the mahine and am wondering will it run on XP, and do I need to install extra drivers etc to run G...
I'm still trying to get some sense out of this set up - any help really appreciated. I've made a very simple profile - for a skirting board. Output to dxf and...
I'm probably being impatient here - ( but that's me ). Cut2D by Vectric does off an output 'direct to printer' although there are two Roland formats listed...
Hi all - Found this useful group as I've just acquired one of these machines.. I thought it was duff because after power up all I could do was jog the...
My spindle motor has a scored commutator and I would like to know if I can turn it down to smooth it out? Has anyone found a replacement for the 100w ac...
Hi all, I am new here and want to say thanks for all the info you have in this group, it was like striking gold when I found it. I have a Camm 3 PNC 3000, it...
Hi everyone, Has anyone got any experience with the CAMM-3 PNC-2700? Is it just a large flatbed version of the PNC -3000? Does it use the same operating system...
Ive been looking to get hold of a Camm3 PNC3000, I have access to one at school and would love one of my own. I have looked on and off on ebay but never seen...
