I had a blown motor controller on my PNC-3000 and finally found a source (obsolete parts broker) of the Sanken motor drivers modules in China. I had to place...
271
dave_mucha
Apr 11, 2010 5:16 pm
Can you send me some data about the drivers ? Dave...
272
tecfacet
Apr 11, 2010 6:05 pm
I would also like to know more about the drivers. Â Roger ... From: dave_mucha <dave_mucha@...> Subject: [CAMM-3] Re: just picked up a pnc-3000 To:...
273
Randy
drlogan2002
Apr 12, 2010 3:41 am
The specifications for the modules can now be found in the files/parts folder for this group. If anyone is interested, you can send a direct email to me...
274
Randy
drlogan2002
Apr 12, 2010 3:44 am
Forgot to mention that there is also a photo of one of the modules in the photos file. Randall...
275
cadcamcreations
Apr 14, 2010 12:31 pm
Hi All, I am thinking about getting some colletts custom made for my camm 3, I had a set made a few years ago but I wasn't involved directly with their...
276
Randy
drlogan2002
Apr 14, 2010 6:51 pm
Hello Graham, Just to clarify, you saying that a complete set of collets (4 pieces) will be ~£200-£300 ? Do you suppose that most of this is machining setup...
277
Randy
drlogan2002
May 2, 2010 5:14 pm
Hi All, I finally scanned all of the missing chapters of the PNC-3000 User Manual. The complete user manual is now available as a single .PDF file in the...
278
david876474
May 3, 2010 11:01 pm
Many thanks to you and your son for that! On a side note: I see we're at 98% full on storage space. Is there anything we can do to improve that without...
279
Darryl
darryl_frees...
Jun 1, 2010 11:20 am
Hi, we have just bought one of these machines but the software was not with this machine. We have some idea what this machine can do and were sent a disc to...
280
david876474
Jun 1, 2010 11:25 am
Welcome to the group Darryl, If you have a look in the files section, ALL of Roland's software is posted there. Download each one and install. You'll also need...
281
db
farmer_dave_db
Jun 1, 2010 2:28 pm
Hi, having problems with the x-axis on this machine. Have owned it since it was new, well almost new. Had 20 hours on it. It was used for a magazine...
282
tecfacet
Jun 1, 2010 3:12 pm
Hello, I would like to purchase a Roland rotary engraver for a church fund raising project. Does anyone know of one for sale at a reasonable cost? Thank...
283
vegas3416
Jun 1, 2010 11:13 pm
Ok, so here is the problem...I have a windows xp laptop and a pnc 3000...I have modela, 3d engraver, and so on and so on...I have my laptop and machine hooked...
284
cadcamcreations
Jun 2, 2010 12:47 pm
... Hi Dave, Had this exact problem many years ago on the camm 3, The stepper motor is connected to the screw with a brass collar and the screw is held tight...
285
cadcamcreations
Jun 2, 2010 12:49 pm
... Hi, I think you might have great problems trying this, I would advise to connect to the Camm-3 by a parallel centronics lead,A few years ago I was...
286
norust2001
Jun 15, 2010 6:21 am
Does anyone know a source for the commutator brushes? Thanks, Sal...
287
Darryl
darryl_frees...
Jun 25, 2010 10:48 am
We have got the machine going and all are very excited but we need to find the following files 3D Design V 1.0 and 3D Text V1.0. We went into the bundled...
288
cadcamcreations
Jun 26, 2010 4:02 pm
Hi, If anyone knows of a PNC3200 Camm-3 for sale, please could you contact me,I have just missed two! One was on ebay but without the controller etc and I held...
289
Brian Bolger
cdmodelz
Jun 26, 2010 7:08 pm
Hi Where abouts are you located? Â Best Regards Brian Bolger ____________________________ CDModelz cdmodelz@... www.cdmodelz.com ...
290
ohartdj
Jun 27, 2010 4:11 pm
My Roland PNC-3000 won't go into check mode Is there any way to run it. ?????? I read the service manual and followed sequince of setting and no luck PLEASE...
291
Dj Ohart
ohartdj
Jun 27, 2010 5:38 pm
Austin, Texas ________________________________ From: Brian Bolger <cdmodelz@...> To: CAMM-3@yahoogroups.com Sent: Sat, June 26, 2010 1:50:49 PM ...
292
roger
tecfacet
Jun 27, 2010 7:11 pm
Please send me a list of any Roland engravers you may have for sale. I am in ohio and need a Roland for a highschool project. Thank you. Roger Gipson...
293
nekpopj
Jun 28, 2010 1:43 am
... Roger, I have a PNC 3000 in A1 shape, but I don't know what it is worth. John Popken...
294
roger
tecfacet
Jun 28, 2010 11:03 am
Can you call me tomorrow to discuss this? Email me: tecfacet (at) yahoo.com Roger...
295
dave_mucha
Jun 28, 2010 11:06 am
what is check mode ? make sure all the cables are conneced. hit the home key and see if that helps....
296
nekpopj
Jun 28, 2010 2:52 pm
Can anyone help me with the value of a PNC 3000 in real good shape? I'm tring to help out Roger with mine but I don't know how to price it. John...
297
db
farmer_dave_db
Jun 28, 2010 4:18 pm
set of collets with machine? My guess is $2500 - $3000 USD for machine with collets set. Farmer Dave From: nekpopj Sent: Monday, June 28, 2010 7:52 AM To:...
298
tecfacet
Jun 28, 2010 4:24 pm
Ha Ha Ha .... ... From: db <dbueckers000@...> Subject: Re: [CAMM-3] PNC 3000 To: CAMM-3@yahoogroups.com Date: Monday, June 28, 2010, 12:07 PM Â set...
299
cyberzl1
Jun 28, 2010 4:43 pm
Wow! What to buy mine? JW ... From: db <dbueckers000@...> Subject: Re: [CAMM-3] PNC 3000 To: CAMM-3@yahoogroups.com Date: Monday, June 28, 2010,...
