Dan, The rapid move problem seems to have gone away. Maybe somewhere something got corrupted. The sizing problem is still very much a problem. Every file I...
248
norust2001
Dec 18, 2009 9:43 am
I am looking for a replacement Switch Panel Console and interface cable for for a Camm-3 PNC-3200. A damaged but repairable unit will be OK too. Thanks!...
249
Steel Wings
norust2001
Dec 23, 2009 6:05 pm
I am looking to purchase Camm-3 mill in working or almost working condition. Although, any condition will be considered! PNC-3000, 3100 or 3200. If you have...
250
dave_mucha
Dec 24, 2009 2:12 am
I have one that is in working order. I can send pics. I need to get $2,500 for it. Not sure how much more it will cost to ship. Dave New Jersey...
251
Steel Wings
norust2001
Dec 24, 2009 4:36 am
Thank you Dave for answering, but I purchased one this morning from another member. Thank you anyway. -Sal ... From: dave_mucha To: CAMM-3@yahoogroups.com ...
252
Jack
txmagnia
Dec 26, 2009 4:10 pm
Hi I want to buy a controller for the PNC3200. Jack...
253
norust2001
Jan 3, 2010 4:04 am
Does anyone have the missing sections of the user manual not posted in the "Files" section? Thanks!...
254
norust2001
Jan 6, 2010 4:03 am
Does anyone know where to get a replacement encoder switch or perhaps recommend a good aftermarket replacement source? The one I have is an ALPS "621U" but...
255
Randall Logan
drlogan2002
Jan 8, 2010 2:39 am
Digi-key has quite a few mechanical encoders. I'm sure many would do the job electronically, but to get the same mechanical form factor might be a bigger...
256
norust2001
Jan 20, 2010 2:42 am
Here's what happened...I purchased a few mechanical encoders from Digikey and found that the one Randall suggested was the closest match. It has a slightly...
257
mikaelglimvert
Feb 7, 2010 2:06 pm
Hello! I am new here in this forum and i wander if any one knows witch post processor I can use to get the right nc code in to pnc-3000? I will work in Catia...
258
dave_mucha
Feb 7, 2010 6:09 pm
There is a post processor in SheetCAM that, I think has a conveter for this machine. Dave...
259
mikaelglimvert
Feb 7, 2010 6:33 pm
Yes I have heard of this SheetCAM, but i want to work in catia only so if any one know witch post processor I can use I wold be glad to know. MG...
260
govande.varun
Feb 25, 2010 11:43 am
Hello All, Recently I was asked to run the Roland PNC 2500 machine by entering G-codes and M-codes. However, I don't have any software or drivers. Need some...
261
dave_mucha
Feb 25, 2010 11:54 am
I am not sure if you got an answer. Did you go to SheetCAM and ask ? they have been great about porting from one software to another. Dave...
262
cdmodelz
Mar 9, 2010 1:41 pm
Hi I am trying to program my PNC300 using Desk Proto. I create the toolpaths from my STL geometry and use the PNC3000 (no spindle control post processor)....
263
cadcamcreations
Mar 9, 2010 2:26 pm
... Can I suggest if you are machining STLs you ditch the desk proto and download Toolchips Quickmill from www.toolchips.com and also download the plug in for...
264
cyberzl1
Mar 9, 2010 4:57 pm
Do you have a link? toolchips.com seems to be some Dutch marketing website. JW ... From: cadcamcreations <cadcamcreations@...> Subject: [CAMM-3] Re: PNC...
265
david876474
Mar 9, 2010 5:17 pm
Try Roland Modela Player. You can download it from our files section. You can import your STL files and directly output to the PNC-3000 from that. Give it a...
266
cadcamcreations
Mar 9, 2010 5:52 pm
... Graham...
267
gigizal
Apr 1, 2010 10:05 pm
Hi All - I have a pnc - 2500 complete with manuals, upgraded material holder & software. I purchased 2 spare motors from Roland 10 years ago and I installed...
268
adamgorres
Apr 7, 2010 9:03 pm
great to find the user manual here thanks! ag...
269
cadcamcreations
Apr 9, 2010 12:57 pm
... A bit of advice before you start using the machine Adam, check that the fuses are the correct rating for the machine, one is in an unscrewable holder near...
270
Randy
drlogan2002
Apr 9, 2010 5:06 pm
I had a blown motor controller on my PNC-3000 and finally found a source (obsolete parts broker) of the Sanken motor drivers modules in China. I had to place...
271
dave_mucha
Apr 11, 2010 5:16 pm
Can you send me some data about the drivers ? Dave...
272
tecfacet
Apr 11, 2010 6:05 pm
I would also like to know more about the drivers. Â Roger ... From: dave_mucha <dave_mucha@...> Subject: [CAMM-3] Re: just picked up a pnc-3000 To:...
273
Randy
drlogan2002
Apr 12, 2010 3:41 am
The specifications for the modules can now be found in the files/parts folder for this group. If anyone is interested, you can send a direct email to me...
274
Randy
drlogan2002
Apr 12, 2010 3:44 am
Forgot to mention that there is also a photo of one of the modules in the photos file. Randall...
275
cadcamcreations
Apr 14, 2010 12:31 pm
Hi All, I am thinking about getting some colletts custom made for my camm 3, I had a set made a few years ago but I wasn't involved directly with their...
276
Randy
drlogan2002
Apr 14, 2010 6:51 pm
Hello Graham, Just to clarify, you saying that a complete set of collets (4 pieces) will be ~£200-£300 ? Do you suppose that most of this is machining setup...
