And they said it was the most over-hyped place they'd ever been. Between the RC guys, the gaggle, and the rule heavy air traffic smallness of the place they...
6mph dead south and 81 degrees: be there or be square!!!! I'm hoping to arrive at the mountain around 1pm... DD the FM ________________________________ From:...
Does anyone have the mapquest address to get directions to Mt. Moore? ________________________________ From: Koen Vancampenhoudt <koen_vc88@...> To:...
Josh, try the Mount Olive Church Road which will bring you to the LZ. The stats of my yesterday's flights: 2 flights 2h30' airtime highest altitude: 2000 ft...
Hello fellow pilots...This years SC Springtime Fly-In is scheduled for May 21,22,23...As usual Friday will be relaxed with an opportunity for those who have...
Go the southern para pilots website. Moore directions and fotos are there. KI4GHF Scrappy out From: Josh Goldstein [mailto:joshcreationsngv@...] Sent:...
Did anyone fly over the weekend? It looked like the conditions must have been perfect? It looks like Tuesday and Wednesday this week might be good as well... ...
Moore Mt. looks quite flyable Saterday and Sunday afternoon (S to SW around 5 mph and sunny). The weather sites predict light winds early and then again later...
I'd love to, but I'm going out of state this weekend for a family function. Fly high and safe! Marc ________________________________ From: willierelihan...
I'm in! It looks to me that tomorrow will be possibly better than today - today starts off with NE but like Willie wrote it will probably be more like L&V...
After a fantastic day of flying yesterday, more of the same coming up today! Yesterday Willie, Torgueir, Chris, Tammy, Ed and myself flew from 2pm all the way...
Awright I’m on it. I’ll be there around 2pm. Scrappy out From: Koen Vancampenhoudt [mailto:koen_vc88@...] Sent: Sunday, April 11, 2010 8:24 AM To:...
Koen, thanks for posting on yesterday's flying and Scrappy thanks for posting that you were going to the hill today. Hopefully, we will have posts tonight or...
Ed, the flying at Moore on Sunday was fantastic. I did not post anything about going because I attended a funeral at 2:00, was suffering from a muscle spasm...
as someone said a day in the air is always better than one on the ground. great day yesterday. It was great meeting new people Steve, hope your back gets...
You got it Doc, yesterday was a great day. We arrived to see kites in the sky. On launch we found Willie, Koen, Andrew, the Torgmeister, Bill (from GA) and...
Great to see some posts on the Buzzard list and even greater to see so many pilots in the air all weekend long. This was without any doubt the best weekend we...
Attention Buzzards It was proposed in an earlier email that we schedule the 2010 fly-in for May 1st and 2nd. Not much was said in response, and I suspect that...
Thanks Steve, for the post. Sorry to hear about your back. Sunday sounds like it was a repeat of Saturday's glass off. Smooth as silk, lift everywhere...
I posted before I saw Scrappy and Koen's reports. Sounds like a great day for all. Thanks again for the posts. Ed ... I posted before I saw Scrappy and Koen's...
LOL, I knew I’d get a response for my wording of that email ;-) I’m just scrappin’ wichya Dan… For the record, Keith DID say, “ that wasn’t...
Since Spring Fling ends April 30 and at least a half dozen of the most active SPP gang are going, I believe they'd be more likely to attend a Moore Fly-in if...
I look forward to both the boat towing and meeting Nathan. Invite him over to Moore, maybe he can join us during the Fly-In. Steve, I'm open for both the...
Fellow Buzzards: I have already made plans which cannot be changed to come to Moore Mountain May 1st and 2nd. Me and at least 1 other pilot will be at Moore...
Nice vid Koen, Cheryl got some vid too, I can't wait to see it. scraps From: Koen Vancampenhoudt [mailto:koen_vc88@...] Sent: Tuesday, April 13, 2010...
An absolutely perfect forecast for Moore again tomorrow, for both thermal and glass-off flying! Unfortunately, unless I can find a babysitter, I won't be able...
