I have been having a similar problem since upgrading 5.2.5.1 & later, currently running 5.2.9.1. All previous versions prior to 5.2.5.1 worked. I rarely use...
Alinco DR-235's are very marginal radios for 9.6k. The ARRL Lab BER testing for them reveals the problem. You can probably pull your PACLEN back to 64 or 32...
Yes deviation and modulation acceptance in the receiver is another determining factor. In other words if you can not receive what is the use! With the g3ruh...
Rather than reply to all I will post all replies here. I am running alinco 235. I have 2 radios sitting in the same room. From what I understand the KPC...
Jeff The biggest problem with 9600 is deviation. Both ends should be around 3 Khz. 9600 also need to bypass all audio amplifiers and filters on both transmit...
Hello, I see you run the com port at 9600 baud, I sugest to you to put it at higher speed like 19200 baud. One of the reason if you receive data on 1200 baud...
Ill look yours over more in morning. But here are mine I use a KPC9612 as well mine feeds an Icom 38A Have you adjusted your TX audio and equalization in the...
We are having problems with consistent connects using outpost. When using hyperterminal it connects better but still retries muliple times. Below are the...
Tony, It is possible there is something that firefox is sending that is upsetting it.I'll try it here with forefox and see what happens, In the meantime it ...
I have been trying to figure out for a few weeks now just why BPQ32 seems to crash at times and need to be forcibly closed via the task manager every few days....
I can help you configure your JNOS properly if you'd like. Tom W1FJE ... From: "mbahicruz" <miguelbahi_cruz@...> To: BPQ32@yahoogroups.com Sent:...
Bill, According to my Tiny-II manual you should link pin 9 to pin 5 (ground) for NETROM or KISS on the serial port. Unlink pin 9 for host mode....
9282
Miroslav Skoric
skoric@...
Nov 13, 2012 5:27 pm
Hi all, I plan to participate in a scientific conference in Osaka, Japan, next April. Related to that I might need some technical assistance by local hams in...
I am in process of finish the startup, of my local node in Elche Alicante, Spain. Thanks to Marc PD4U ( my link partner ), and his help. The node is ready for...
Howdy Gang, Is anyone here on BPQ a X1J4 Expert as I have a question about the HOST mode. We are attempting to hook up a Kantronics KTU with Weather Node...
Mike, The periodic broadcasts continued for a couple of days and then ceased. There are no node broadcasts of any kind. I will make the changes on the second...
Hi All, After testing BPQ32 etc for quite sometime now, I have decided that running the extra computer just for testing is not really worthwhile. There for, i...
Dave Is you second BBS also BPQ32 node, if so in the port that is making the connection To your first BBS add in that port NOKEEPALIVES=1 How do you have the...
Mike, Thank you. Made the changes and all node broadcasts have disappeared with the exception of one. This is a significant improvement. Every two minutes the...
Hi, You dont have to do anything special to allow both ports to connect to the BBS, A connect to the BBSCALL on either port will work. When forwarding out, the...
I have 3 frequencies feed my BBS. 1 VHF and 2 HF. In my case each HF frequency has it's own radio and Pactor modem thus, it's own port. From what you are...
Not sure if someone has asked this but I am trying to have 2 different frequencies feed into the BBS. I am using a KPC 9612. I have setup the config with...
Comment: BPQ32 Igate V 5.2.9.1 Last status: W9JUN BPQ32 Winmor 7.061 USB (dial) WLNK-1 Madison, IN Last beacon: W9JUN BPQ Packet Node in Madison, IN The above...
