Note: forwarded message attached. __________________________________________________ Do You Yahoo!? Tired of spam? Yahoo! Mail has the best spam protection...
Note: forwarded message attached. __________________________________________________ Do You Yahoo!? Tired of spam? Yahoo! Mail has the best spam protection...
The message "new graphics site" circulating via Yahoo Groups is a virus. Do not open the attachment. I just received this message as being sent to the Allard...
Greetings, Jim Donick's J2 was featured in one of the My Classic Car segments on Sunday. The episode is about the Mt. Washington hill climb. Usually they show...
My 1950 K2 Allard is nearing the completion of its restoration. The windscreen does not fit properly. Since I purchased it three years ago completley...
Andrew Picariello
afpic@...
Jun 13, 2006 3:11 pm
3750
Andrew, can you put a picture of the windscreen you have on your car. I have on my car a brass frame and it is tolly different than the K2 cars. Thanks William...
Gentlemen, is it July that you will come up here? I was so shocked when I saw the ad from our local parts distributor that sponsors the race that my jaw...
Vince, Thanks for the info. on Bill Pollack I have copied this to the Allard chat-room site, and to Bob Lucurell, the sponsor of the event. I hope to see you...
Andrew Picariello
afpic@...
Jun 20, 2006 8:51 am
3754
Good morning All, Would anyone know the current rate of U.S. $ to the British Pound? What would 210 Britt pounds be equal to in U.S. dollars? Thanks,...
Barry: You can go to the following website: www.oanda.com. It is a foreign currency site that will give you the daily rate for all currencies and do a...
In a message dated 22/06/2006 13:33:16 GMT Standard Time, ... Barry Conversion at 13.50 hours for £210 was $387.659USD David In a message dated 22/06/2006...
I recently purchased a K3 without the deDion rear end. I am interested in replacing the existing solid axle with a correct rear axle - suspension layout. Where...
Good morning Howard, Do you intend to fabricate the parts if you cant purchase an existing set up? I have a J2 here in my shop that I'm about to install the...
Good morning Howard. If you get some dimensions from a J2 the K3 axle is 6.5 inches wider than the J2 (58.5 inch track), also the drive shafts are each 3.25...
... axle is 6.5 ... are each ... differential unit. ... David Hooper. ... Hello Gentleman,I'm also looking to build a DeDion back axle but I need it for a...
... interested ... Howard , I am restoring K3 3282, and have a ton of digital pics. The car should be back from the exhaust shop tomorrow so I can get you any...
Hi All, I seem to be creating messages that end up in other people's messages , or not there at all so excuse me gentlemen. I'm quite new to this wizardry...
Mel: You should be able to find a Ford 3-speed almost anywhere -- but is this what you really want? The Ford 3-speed will not withstand the torque of a Caddy...
Thanks Dean, I'd much prefer a Cad-LaSalle but thought they were likely to be like hen's teeth. Do you have any leads ? What year were the later Caddy heads...
The later Caddy heads are, I think, 1953 -- could have been some time in 52. You should be able to find a Cad-LaSalle through Hemmings. A guy I know over here...
Greetings Fellow Allard Enthusiasts, Cadillac cylinder head info: 49-51 same, 52-55 similar, 56-63 similar. The main difference in the heads is the exhaust...
Thanks Dean and Barry, Following your comments I have contacted my supplier and told him that I would prefer a 390 engine .Do you have contact details for...
hi: I posted a message recently asking for help in reconstructing a deDion for a K-3. I neglected to add that I am also in the market for appropriate parts. I...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
