Thanks for the comment re: don't ponder too much. When I was working with Mac on my Wee Lassie one day, I was sanding it as if it was a Louis IV table; Mac...
897
mgrogg@...
mgrogg51
May 4, 2010 8:51 pm
A friend closed down his basement canoe shop and bequethed me a bunch of cedar strips, all set to build something beautiful and sleek. The boat I'm considering...
896
second_floor_loft
second_floor...
May 4, 2010 7:19 pm
Beau: If you haven't seen this yet, go here... You can try to PM him for more info. ...
895
bschless@...
bschless
May 4, 2010 6:51 pm
A friend closed down his basement canoe shop and bequethed me a bunch of cedar strips, all set to build something beautiful and sleek. The boat I'm considering...
894
second_floor_loft
second_floor...
May 4, 2010 5:03 pm
The kevlar roving is no big deal. In my case, I made a quick layout to cut it out using a length of board and a dowel for an axle for the kevlar to spin on.....
893
Eric
tanzerman1944
May 4, 2010 2:49 am
Well, I guess I'm not really a newbie, I have been a lurker for about a year. I finally took the plunge the other day and ordered the plans and the partial kit...
892
Eric
tanzerman1944
May 4, 2010 2:12 am
Here is a link that will guide you in building a sail for your boat. Doesn't look very difficult. http://www.boat-links.com/Tyvek/...
891
bschless@...
bschless
May 3, 2010 12:33 pm
Learn to paddle harder on the side where the bend is! Beau Schless NOTEbookS Library Automation (978) 443-2996 http://www.rasco.com From: "aolsmile42"...
890
aolsmile42
May 3, 2010 12:14 pm
Hi there, I'll have a go at answering these questions - they seem eerily familiar..... 1) That happened to me on my first Snowshoe14. There's not much, if...
889
chazzelwood
May 2, 2010 11:01 pm
I'm working on my first Snowshoe 14 and I had a few mistakes that I hope won't bite me later on when I put the boat in the water: Here are the issues: 1) When...
888
Bob & Kay
trawler10
May 1, 2010 3:40 pm
Thanks and it appears from your photo site (very nicely documented I might add) that you did a really nice job on her. I built a stitch and glue Cats Paw 10...
887
Peter
pjacobs55
May 1, 2010 3:19 pm
Bob, I'll keep you posted. I suspect I'll have to put a clear coat of varnish over it, as I already scuffed it a bit bringing it over the rail of my sailboat....
886
Bob & Kay
trawler10
May 1, 2010 4:31 am
Peter .. Am in the process of building a Classic 12 - tomorrow will finish gluing in the ribs -- was interested in your choice of paint and might be ...
885
Peter
pjacobs55
May 1, 2010 1:10 am
I finally launched the Black Fly today. I've added photos, comments, etc at www.sintacha.com. Peter....
884
Peter
pjacobs55
Apr 28, 2010 4:59 am
Just my opinion: Titebond would probably do fine, as long as your wood joints fit together without any gaps. It's a very nice glue to use as the cleanup is...
883
chazzelwood
Apr 27, 2010 6:26 pm
I noticed that the instructions for the Snowshoe 14 calls out for Epoxy. I found a Type 1 water resistant Wood Glue called Titebond III. Has anyone tried...
882
Peter
pjacobs55
Apr 27, 2010 3:46 am
Interesting ... I found the same in the Black Fly, although I haven't yet been on the water. But I compared it with my Eastport Pram, and moved the seat,...
881
Bob & Kay
trawler10
Apr 27, 2010 2:36 am
Paul … thanks … that did indeed clear it up … appreciate you digging out your old plans to assist with this …. Back to bending ribs…. Bob From:...
880
second_floor_loft
second_floor...
Apr 27, 2010 12:34 am
Bob: I'll make a guess here that when you refer to two different sizes indicated in the plans you are talking about the "Bill of Materials" section on the...
879
second_floor_loft
second_floor...
Apr 26, 2010 10:27 pm
Ummmmm.... I really don't remember. I'll dig out my plans and see what the deal is. It's been quite a while ago. "I'll be bach".. Paul ... From: Bob & Kay...
878
bschless@...
bschless
Apr 26, 2010 6:35 pm
I mad a pretty successful steam box out of several pieces of plastic PVC drain pipe, a tea kettle, and a hot plate. The only problem I had was the drain pipe...
877
second_floor_loft
second_floor...
Apr 26, 2010 5:47 pm
Regarding steaming wood. Yes, all wood in the big box stores is kiln dried. You'll likely need to find a saw mill near you to get wood that isn't. I think in...
876
Bob & Kay
trawler10
Apr 26, 2010 4:27 pm
I am in the process of bending oak ribs for my classic 12 and in an old dvd from the Boatshop found an excellent and inexpensive way to construct a simple...
875
Bob & Kay
trawler10
Apr 26, 2010 4:16 pm
Thanks for the advice. I will take you up on the pix . bkmcintosh@... . also, did you see my note to Paul T. re the dimensions of the gunwale blocks...
874
bpofak
Apr 26, 2010 4:11 pm
Thank you both for responses. I don't intend expect to need steam for the longitudinals. But, I did steam a length of 3/8 x 1/2 oak from HD that was clearly...
873
bschless@...
bschless
Apr 26, 2010 4:09 pm
I followed the instructions on gluing in the middle seat and oarlock blocks on my Classic 10, only to discover that with a passenger the seat and oarlocks were...
872
Bob & Kay
trawler10
Apr 26, 2010 3:21 pm
Paul T …. I in installing ribs in my Classic 12, (nearly all in) and curious about dimensions of gunwale blocks as plans allow for two sizes … what am I...
871
Hajo Smulders
hilomania
Apr 26, 2010 2:18 pm
Do you intend to steam bend that pine or just use it for the stringers? I'm asking since I suspect that most home depot pine is kiln dried. I'm wondering how...
870
second_floor_loft
second_floor...
Apr 26, 2010 1:51 pm
I don't think pine would be classified as softer than DF or Spruce. Also, using the boat in protected waters, it'll be plenty strong the way it is designed...
869
bpofak
Apr 26, 2010 4:08 am
Stems and forms are in place and I am about to get started. However, I have been unable to find suitable spruce, doug fir, etc. so I am planning to use...
