Folks, I finished my ATS - 3B a little while ago and built the simple interface cable to connect it to my IPaq 2210. While the PocketDigi on the Ipaq works...
Andreas, To check the simple things first, are you putting the ATS3B into Digital Mode before connecting the cable? 72 Stephen VE7NSD ... -- "You never change...
Hi Stephen, I made sure that the ATS3B is in digital mode before connecting it. 72 Andreas kg4pyp ... Digital ... PocketDigi ... attached ... simply ... the ...
Hi Andreas. ... I do not wonder that ATS is picking noise from the switched power supply. Run it on internal battery. ... The simple interface requires quite...
Hi Stephen, Â thx for yoru feedback. yes I did of of course. Â I wonder if I should build the more complicated interface ! Â 72 Â Andreas kg4pyp ... From:...
Hi Andreas, I suspect that Vojtech's advice to you is probably the best, since he is the one who made digital mode possible on the ATS rigs. Can get the ...
Will this iPAQ suffice for digital mode operation with my ATS3B? Thanks 72 Stephen VE7NSD -- "You never change things by fighting the existing reality. To...
... I wonder what is the difference between 3630 and 3650. PocketDigi was developed mainly on iPaq 3630. The biggest problem of the device is high backlight...
Hi, I'd like a wider audio on my 3B! The narrow noise sounds almost like ringing to my ears, whereas I can tolerate my IC-703 at 500Hz bandwidth a lot better! ...
... I replaced the three caps with varactors and I tune bandwidth from zero to about 1.5kHz. At wider bandwidths the response is not flat. The minimum capacity...
Vojteck; If you were to select around 400-500 Hz bandwidth, and reasonably flat, what capacitors would you suggest for c5, c6 and c7? I've ordered up a kit of...
San Diego Electronic Supply [http://www.sdelectronicsupply.com/] has a terrific inventory of discrete components including SMD. He also is adept when finding...
Just posted photos of the ATS work/maintenance station at KT6L. Located in the "reading/music/tv" room of the house, the paint pan and panavise make ...
I'm working on it. Just ordered the main board today, next will be the filter boards. Then I guess I will have to start collecting the parts. Since the guy who...
Last month I finally got around to assembling my second 3B which came from the last run. I was having trouble with the solder paste from Cash Olsen being too...
Hi Jim. ... I received a parcel from Mouser today with lot of parts for my next homebrewing. Among them there are some 3 digit LCD displays and bunch of 8bit...
VojtÄ›ch BubnÃk wrote: If it works, it will be a blast. ... If it works, I hope you will document it carefully and post it to the files section of the list....
HI Steve, Good to see you. One other addition to your list... us that have one of each of your designs.... and can't pass getting the next one too.. They each...
Hi Jim. ... The idea is to feed three 74HC164 8bit shift registers by two pins (data & clock). Only for clock an exclusive controller pin is needed, data pin...
Thanks for the info. I have carefully saved it. Now I just have to stop being lazy and build my radio. :-) 73, Jim Jim Larsen http://www.AL7FS.us/ Anchorage...
Steve, Put me down as a potential buyer! How does it work, though? Is there already a waiting list, or will it be first come, first serve from the day it...
... With Steve, it's always been "first come, first served". He does not "do" waiting lists. It's just too much hassle to keep track of. He also does not...
Possibly off-topic: I was wondering if there were more efficient heat sinks available that would help to protect the PA in the ATS seriess - I remember seeing...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
