... Russell, I'm interested in the tooling in photo #5 http://ph.groups.yahoo.com/group/7x10minilathe/photos/view/9bb7?b=5 Is that 1/2"? What is on the green...
Jon... Â both of those are measure 1"...the one sitting on top of the green box goes in the green box...on the end of the box is this..."C-MRGNL-16-4 ...
If you have a dovetail QC post, you can cut a dovetail in that 1" shank and it becomes it's own tool and holder ! Since the shank is soft enough to be...
I need to rewind a solenoid the power the way oil pump on my surface grinder. I'm planning on putting the core on a mandrel and spinning it with the lathe to...
My last post mentioned messages slowing down here. Turns out they have NOT slowed down, I am simply & suddenly not recieving any at all. This list and the...
Check your junk or spam mailboxes on your local PC as well as your server? Ask your service provider if they are blocking it? Try sending yourself an e-mail...
Syd's coils:http://www.logwell.com/tech/CCL/CCL_coil.html I think poly is the most chemical resistant, but that would be just my guess. Shane ... remained of...
Boring bars need a lot of front clearance. I set mine a little above the centerline, so the if there is a little spring in the tool due to the long overhang,...
The solenoid armature is the piston of the oil pump. It works against a spring and cycles at 60 Hz. The solenoid was originally running off two legs of the the...
It doesn't sound pretty. If I'm not mistaken, the 3-phase is 208 from leg-to-leg, so I think it might run a little warmer on 220. Perhaps a heat build up...
185587
AnaLog Services, Inc.
analog@...
Jun 2, 2008 2:12 am
You do not have to use the varnish. The cloth you are seeing is likely fiberglass tape, but most anything will work. Regular vinyl tape will become brittle...
Thanks Mert, but how do I find the centerline? jon ... above the centerline, so the if there is a little spring in the tool due to the long overhang, it will...
jon, Personally, I set ALL tools at center. I have a little dedicated "height gauge" that I use for all tools. Worked for me, (for the last few decades). Dave...
You want to make what the industry calls a carbonator. It has been a while for me but my recollection is that this is a stainless steel chamber full of co2...
I don't have any way to know how many turns were on it. I just intend to wind 36ga magnet wire on the bobbin until it looks full. I'm going to change the...
... Turns out in email settings on Yahoo you can check for bounces - emails sent to you from yahoogroups - that were bounced back for whatever reasons. There...
AnaLog Services, Inc. wrote: You do not have to use the varnish. The cloth you are seeing is likely fiberglass tape, but most anything will work. Regular vinyl...
Hi all, I attempted to sharpend a 3/4 " drill today and had the worst results. seems the grinder made the cutting edge shallower than the relief behind it....
... shouldn't the depth and cutting sections be at the same angle (118&118) ? anyway I've found that when taking a heavy grind on larger drills the drill will ...
The lathe centerline, (cl) or (CL), is on the point of the TS center. I used to carefully set a pointed toolbit on it, and then use the toolbit to scribe a...
My drill doctor is the smaller one, & I have been sharpening all my large drills by hand, eye, & gage. Not too hard, really, and surely avoids the problem you...
John, Did you clear out your "bounce" record? Since I filter out a lot of spam messages on my email server, and toss them back, Yahoo tends to stop sending me...
Dave, Any kind of drill sharpener that requires 'timing' the drill by indexing the cutting edges against a setting fixture will do exactly what you described...
Spent the day over at Dave Mucha's place yesterday. It's about a 2 1/2 - 3 hour drive from where I live in Southern Maryland to the Pine Barrens area of New...
We mucked around trying different things for over an hour yesterday. Even tried reading the manual... Just couldn't get the damn thing to grind the cutting...
John, If I recall. If Yahoo receives a certain amount of undeliverable messages it will suspend your account. There is some action required on your part. I ...
