Hi! Tried yesturday to program the chip, but when starting the prog08sz.exe I just got some error message. It said illegal action on some memory block or...
Yo, Excuse me for asking, but why would someone want a stand-alone programmer? I use an in-circuit programmer/debugger that cost less than $10 to build and...
Hi samilappalainen, My comments are embedded Wednesday, September 1, 2004, 6:15:55 AM, you wrote: s> Hi! s> Tried yesturday to program the chip, but when...
Hi Greg, My comments are embedded Wednesday, September 1, 2004, 4:37:31 PM, you wrote: G> Excuse me for asking, but why would someone want a stand-alone G>...
Thanks for the fast info :). This helps a lot. I will give it a try during weekend and get back if there is any problems. Thank you again for fast response....
Greg I'm trying to get into the 68ch908 programming. What is the board and software that you are using and where can I get it? I really like to no as mush as...
Want a free desktop pc? Well... here is a way how. I have done my research and this appears to be totally legit. Be forewarned, you need to live in the US to...
Can you believe I refinanced my mortage and am saving $386 a month? Check it out... http://edgelending.com/?partid=rcc2 If you dont want to be part of this...
Can you believe I make just 4 extra payments a year and will pay off a 30-year mortgage in only 9 years? And saved myself FAR more than a measly $386 a month...
Hi! Well, I changed the prog08sz to C: root and it started working just fine...Blank chip in(It is nice to have switch on board by the way when asked to switch...
I also tried to hook it up to 9.v supply..no results. Could the problem be in program security check passing? as I recall the 08sz starts reading the memory...
Stupid RTFM question, maybe... If one chooses to use an internal clock on the KX8 device, how can one do this when the microcode itself uses the same internal...
Refinancing your home is never easier and more profitable. Our staff works exclusively to save you the most money as possible on any home loan. We secure loans...
I have bad credit, I am self employed and I was able to re-finance at a really low rate. I am saving hundreds a month Just fill out this simple FREE form for a...
Re-finance now, even with bad-credit! *Best Re-finance Rate for credit challenged. *Best Customer Service *Lowest Interest-Rates in Years *SAVE $100-$400 per...
... being ... Answer to my own question: Freescale AN2508 page 18 states that for KX8, after reset: - TRIM = 0x80 - fbus = 1.613MHz with ICMGR register...
... being ... Answer to my own question: Freescale AN2508 page 18 states that for KX8, after reset: - TRIM = 0x80 - fbus = 1.613MHz with ICMGR register...
So I built my own copy of the programmer, powered by a 9v wallwart and a manual switch. By the way Jim, thank you for the design. Now for the question: How...
Hi aerowerks, My comments are embedded Tuesday, October 19, 2004, 5:46:38 PM, you wrote: a> How long should it take to program the S19 file into the flash?? ...
Thanks Colin, the programmer works well somewhat works. The reason why I asked how long it takes is because it took split second for programming, after doing a...
Never mind, I figured it out. Turns out that it was a problem with download. Virus/ergh Windows Internet Exploder defaults any file extensions it does not...
Re-finance now, even with bad-credit! *Free No Obligation *Best Re-finance Rate for credit challenged. *Best Customer Service *Lowest Interest-Rates in Years ...
Interest rates are as low as they can possibly get. Be sure to take advantage of this possible once in a lifetime opportunity. Better interest rate means lower...
Hi All has any one had success with PROG08SZ using a USB/SERIAL adaptor (Bafo-810) to flash a blank 68HC908 ? PROG08SZ is running from a folder on :\C I Have a...
I have Willette programmer and Prog08sz v1.2 Embedded code v3 First I have erased module and then check the module, which claims that's erased. Then I choose...
Hi wiima63, My comments are embedded Tuesday, October 26, 2004, 12:46:48 AM, you wrote: w> Then I choose the module .s19 w> When I'll try verifying module I...
Okey! I'll try again and find some other commands. Thanks, Colin Jani ... or ... http://thegebharts.com ... http://www.ritlabs.com/the_bat/index.html ... ...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
