Yes, it’s a real com-port integrated at my motherboard (MSI K8N Neo4) The com-port work fine with Megatune. Any other suggestions? /Vessel _____ Fra:...
Hi Vessel, My comments are embedded Tuesday, June 7, 2005, 3:24:03 PM, you wrote: V> Yes, it’s a real com-port integrated at my motherboard (MSI K8N Neo4) ...
This is very embarrassing… After I have gone througt the diagrams over and over again, I figured out that I have inverted the (-) and (out) pin on the ...
Staff, I can usat a crystal of 19.6608 of 2 terminals that were removed of an old fax modem? I ví that in pcb he only uses 3 terminals, in the case to use the...
Hi zico_s28, Monday, May 1, 2006, 1:17:15 PM, you wrote: z> I can usat a crystal of 19.6608 of 2 terminals that were removed z> of an old fax modem? Hi Zico, ...
I mounted the programmer, but when beginning prog08sz asks for a security code that I do not obtain to find, that code is this? I bought a blank controller,...
Here it happens the following one, I connects, asks for a security code to enter, I gives to ignore the code, it enters, I give to verify chip to see if he is...
Hi! When i try to program a new chip, the software ask for a security code? I have connected a 9V battery to the programmer. There is 6.0V on pin 1 at the...
Hi Sebastion, Its been a long time since I burned a megasquirt.s19, but from memory the bootloader normaly is a seperate .s19 file. It loads into memoryation...
Sebastian, Using a 20Mhz crystal would cause a baud rate of 19.53125 Khz. That could be too far from 19.2 khz to be usable on a serial port. I have read that...
Hi I was ready to program mi 68hc908 but I noticed that I bought a cristal and not a oscillator like the circuit. Is there any way to use a cristal of instead...
... have ... The easiest way is to use an oscillator. You would have to re-design the circuit to use a crystal. Look on the freescale.com com site for info on...
Hi in the notes of this group I read that if I dont have de 11 volts od the serial port I should put a 9v battery to the collector of the transistor. Thats ok,...
Hi I am back, I just finish mi pcb and I try to program. First of all I tell us what I am running: Is the same circuit but I add an 7805 and a switch to...
Sebastion. you are getting there. I would suspect serial timing issues using a 10mhz crystal. Also what computer are you using older slower...
I have no idea if this will help anything, but if Jim's second suggestion is right and your computer is too fast, this program will slow it down. It worked...
Well I tried with 2 cpueater.exe and I burn it ok, is better but when I put it on the mega board it does not work. I make a mistake my verion of prog08sz is...
here are the boot.s19 and the mega.s19 I am uploading, maybe I compiled wrong. I do not know ****boot start here S113FB0002C0038402D003D14FC7FFFF6E011E6EF3 ...
Sebastion. Try using the loader mode on the megasquirt with hyperterm connected to the megasquirt check your serial port rate. See if you get the loader...
I have just tried but the boot> prompt does not appear, it is dead. I tell us that my cable y ok, and the max232 was testead and is ok. could I test on the...
Sebastion, Its been a long time since I worked with the programing software, but if memory serves me correct you can verify the code on the chip with...
Well I answer yours questions. ... if memory serves me correct you can verify the code on the chip with the file you programmed it with in order to determine...
Good news on my mega board was a cap 24 wrong it is 22pf and I put a 220000pf mistake! so the osclilator was wrong. But allways was burning ok prog08sz. Now I...
Congratulations Sebastion Your perseverance paid off. I am happy to hear you were able to get your Megasquirt programmed and responding. ... From:...
Thanks a lot to the group! this is the best. And for those who does not find the 9.xxx Mhz oscillattor try the 10 Mhz that worked for me, and I use a 7805 and...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
