" -----Please tell me where the factory mirror mounts on the right side casting. I would like to hear from more than one person. This is to settle an...
40784
deeter162002
Jun 22, 2012 12:21 am
Here you go, Allen: http://groups.yahoo.com/group/5united/files/Jack%20Clarke%20Schematic/ One of those should enlarge for you and help to figure out what you...
40785
cwilson5@...
christopher....
Jun 22, 2012 1:07 pm
Mine is in the same place. Date of manufacture 5/71. Sent via DroidX2 on Verizon Wirelessâ„¢ [Non-text portions of this message have been removed]...
40786
Mehosky, Brian L.
brian.mehosky@...
Jun 22, 2012 7:38 pm
For those of you who did not get out on you scooter last weekend, you really did yourself a disservice. The weather was, pretty much, perfect for riding. I...
40787
lewmoco1131
Jun 22, 2012 11:19 pm
A really simple set-up would be a wire directly from the battery + to the coils to make the engine run, kick start the bike, and then disconnect it to shut off...
40788
Glenn
radz752002
Jun 22, 2012 11:20 pm
Does any body have a set of fuel taps and fuel cap (old non locking type) for a /5. Glenn in Oz...
40789
jmayocullen
Jun 23, 2012 12:38 pm
I'm replacing fuel lines, and it is very difficult to push the line over the nipples. Any suggestions from the group to make it easier would be much...
40790
John Robertson
jock_ey_club
Jun 23, 2012 12:40 pm
Hi Folks, If anyone is in the area of Nakusp, BC (east of Penticton) in mid-August and wants to meet other BMW (mostly) riders check out the rally web page: ...
40791
Toaster.Tan
toasterrider
Jun 23, 2012 3:10 pm
WD40 Stephen custom top braces http://www.pbase.com/toastertan/top_braces From: jmayocullen Sent: Friday, June 22, 2012 4:59 PM To: 5united@yahoogroups.com ...
40792
Chris Redding
kiffer_8
Jun 23, 2012 3:36 pm
Big or small, thick or thin, K-Y jelly will get it in..... Cheers Chris Redding sues_place@... To: 5united@yahoogroups.com; jmayocullen@... From:...
40793
Chris Waymire
olliew72
Jun 23, 2012 5:26 pm
Are you sure you didn't get the 5 mm line instead of the 7 mm? I had that problem once. Chris...
40794
lewmoco1131
Jun 23, 2012 5:27 pm
If it's that hard to get on, is it the correct size line?...
40795
Thomas Gaitanis
linustag...
Jun 23, 2012 5:30 pm
"Instead, I topped it off with fresh hypoid until it was totally full, and then sucked out the excess using a non-disposable 50 cc syringe that I purchased...
40796
Phillip Jordan
phjbmw
Jun 23, 2012 5:35 pm
... The breather tube is still available from Motobins - part number 11420. ... If the oil seal on the input side of the bevel drive is allowing oil to migrate...
40797
Lyman R
motorrun2003
Jun 23, 2012 6:26 pm
Just bore a bigger hole in the - bolt the battery cable attaches the assy breaths from Lyman Lyman...
40798
Duane Ausherman
w6rec@...
Jun 23, 2012 6:29 pm
Once again the transfer problem isn't as it appears. It isn't a matter of replacing a seal, as that will probably do nothing. You could do a Google search and...
40799
johnfalc@...
johnfalc
Jun 23, 2012 7:35 pm
In case you want to ride along vicariously: http://cyclecircuit.blogspot.com is a blog I update as I go along. John Falconer (from my phone) ... From:...
40800
Duane Ausherman
w6rec@...
Jun 23, 2012 10:17 pm
Bill and others; Always remove the fill plugs first. Always drain into a measured beaker and record it. Always fill from a measured beaker and record it. The...
40801
William Wilson
wilsonpaintco
Jun 24, 2012 2:10 am
This all may be a non-issue. If the lube seeps back when the RD is lower when parked then it probably seeps back forward when it's level with the swingarm...
40802
tfours@...
fourties_2000
Jun 24, 2012 2:10 am
Try immersing the fuel line end in boiling water for a couple of minutes [Non-text portions of this message have been removed]...
40803
agentagent9
Jun 24, 2012 2:11 am
Does anyone happen to have the tool for removing the drive shaft bolts I could borrow in San Francisco? I thought I was all set on tools for a clutch...
40804
Carl Robinson
carlrobin
Jun 24, 2012 2:27 am
You should have a twelve point box end 10mm wrench to fit the drive shaft bolts! If you are referring to the 27mm thin wall socket for the swing arm pivot pin...
40805
Stephen Chase
esahcs
Jun 24, 2012 12:37 pm
Ezra, Why not consider making the tool. It would cost less than $15 with Craftsman tools. It's easy if you have a welder friend. Check how to make it on...
40806
Duane Ausherman
w6rec@...
Jun 24, 2012 6:47 pm
I just listed a boxful of BMW special tools on eBay. Someone may get them cheaply, as I don’t know what most are for. I haven’t used them for over 35...
40807
Kim Dromlewicz
dromlewicz
Jun 24, 2012 9:04 pm
... bolts! This is correct except that the box end must be thin walled enough to get between the bolt head and the shaft coupling wall. Most Craftsman box...
40808
Eric Schmitt
ecrs32960
Jun 24, 2012 11:23 pm
I grabbed a non-craftsman 10mm from sears, what ever their cheap brand is/was. Fit perfectly...If you can find one of those then Roberts your Dad's Brother. ...
40809
Lyman R
motorrun2003
Jun 24, 2012 11:30 pm
Mine works very well Lyman...
40810
js wilson
bigtreepine
Jun 25, 2012 12:05 am
Most Craftsman box ends are too thick walled around the 12 point section SO grind /sand the wall thickness down and remove the inside chamfer off the top and...
40811
Mehosky, Brian L.
brian.mehosky@...
Jun 25, 2012 12:29 pm
Other list members have indicated that the breather tube is available from Motobins and Hucky's. It was shown as NLA on Max's parts list. A re-designed tube...
